9 More Discussions You Might Find Interesting
1. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
2. AIX
Have been learning a lot off late and am a little unclear about the VIOS setup particularly with regards to redundancy. Would appreciate your help.
My question is very basic. Lets say I have setup a VIOS and 3 LPARs on only one hdd (non scsi). On what do I setup the second VIOS? Could I for... (7 Replies)
Discussion started by: theaixeman
7 Replies
3. AIX
Hi Guys,
I'm working on building a new 595 machine.. I'm try to achieve high availability for the VIO clients using 2 VIO servers, The ethernet part is satisfied using SEA failover, Now how do I achieve redundancy for the disks, its the servers internal disk attached to the scsi cards...
... (2 Replies)
Discussion started by: kkeng808
2 Replies
4. Solaris
Hello,
Yes, it's me again. Running around getting this done! My current problem is I'm trying to image one drive 0 (/dev/dsk/c1t0d0s0) to drive 1 (/dev/dsk/c1t1d0s0). I know that drive1 came out of a Sun Server and it is a Sun drive. Solaris 10 recognized drive1 after the devfsadm command. The... (8 Replies)
Discussion started by: adelsin
8 Replies
5. Red Hat
Can anyone recommend an imaging solution for RedHat Linux that would allow base imaging with the ability to do incremental updates and encryption? I know Acronis has a version available, but it is rather pricey.
Thanks. (0 Replies)
Discussion started by: here2learn
0 Replies
6. UNIX for Dummies Questions & Answers
We have had some email outages in the last few months and my boss is asking is it worth going with one of those email redundancy/filtering sites. The thing is, we have a backup server on a remote location, so I am pretty sure we can set something up with what we have already.
At the moment... (1 Reply)
Discussion started by: edzillion
1 Replies
7. UNIX for Advanced & Expert Users
Here we want to implement the network redundancy on UNIX with the software.
The two network interface cards are configured on the UNIX node,once one card is down or unnormal,the other can take over. Those aplications that used the tcp ,udp,multicast protocol can also been switched at the same... (2 Replies)
Discussion started by: Frank2004
2 Replies
8. UNIX for Advanced & Expert Users
Dears,
I have server has two port's(Enet0,Enet1) what I want as follows:
Make the two port's has same IP address
where, if the port Enet0 became down automaticly Enet1 become up :confused: .
Amen (4 Replies)
Discussion started by: amen00
4 Replies
9. UNIX for Advanced & Expert Users
Does anyone know of any good imaging tools that can be used to create an image of a Sco-Unix box? (2 Replies)
Discussion started by: gmrfh1
2 Replies
BOOT.CONFIG(5) BSD File Formats Manual BOOT.CONFIG(5)
NAME
boot.config -- Configuration file for the boot blocks
DESCRIPTION
The boot.config file contains options for the FreeBSD boot block code.
When the FreeBSD boot loader runs, it searches the ``a'' slice of the boot partition for a boot.config file (as a result, slices which are
missing an ``a'' partition require user intervention during the boot process). If the boot.config file is found, its contents are used as
the default configuration options for the boot block code and are echoed to the system console.
A valid format of this file is to put BIOS drive number, a controller type, a unit number, a partition, a kernel file name, and any other
valid boot(8) option on a single line, as it is done at the ``boot:'' prompt.
The options related to the boot image selection described below and all the other options available for boot.config are documented in detail
in the boot(8) manual page.
FILES
/boot.config parameters for the boot blocks (optional)
EXAMPLES
The command:
# echo "-P" > /boot.config
will activate the serial console of FreeBSD.
The command:
# echo "1:ad(1,a)/boot/loader" > /boot.config
will instruct the second stage of boot(8) on the first disk to boot with the third boot(8) stage from the second disk.
The command:
# echo "1:ad(1,a)/boot/loader -P" > /boot.config
will do both of the above.
SEE ALSO
boot(8), loader(8)
AUTHORS
This manual page was written by Daniel Gerzo <danger@FreeBSD.org>.
BSD
May 13, 2007 BSD