10 More Discussions You Might Find Interesting
1. HP-UX
Hi Guys,
Kindly advise how to fix the down interface status in MC.
Physically all nic interfaces are ok but as cmviewcl some interface are down:
Node 1:
Network_Parameters:
INTERFACE STATUS PATH NAME
PRIMARY up ... (0 Replies)
Discussion started by: batas
0 Replies
2. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
3. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
4. Debian
Hi, i have problems with an installation of Debian i386 505 in a pc. The hardware it is a mother soyo with a chipset via.
When i install the xorg, the installation it`s succesfull, but when i type startx, the pc don`t respond.
I am from Argentina and my English it isn`t good. Sorry. (0 Replies)
Discussion started by: Kritar
0 Replies
5. Programming
Hello, I'm trying to use libcurl multi interface to fetch several data in parallel. I would expect this to be faster than performing repeated fetches using the easy interface, but for some reason I can't obtain any speed up at all: using the multi interface actually turns out to be MUCH slower than... (2 Replies)
Discussion started by: clalfa
2 Replies
6. IP Networking
Hi all,
I am experiencing a problem with dhcp broadcast packages. these broadcast packages are seen on bge1 and bge1:1 interfaces but somehow they are not seen at bge771001 interface which is second virtual interface on the bge1 interface.
I have a server on which I configured it as working... (2 Replies)
Discussion started by: ironoxide
2 Replies
7. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
10. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies