In Case You Missed It: MonoDevelop, aC# IDE for Gnome Developers - InfoQ.com
In Case You Missed It: MonoDevelop, aC# IDE for Gnome Developers InfoQ.com, Canada - Jun 14, 2007 To create a best of breed development environment for Unix systems for Mono. Since its written in Gtk#, and we like Gtk# and we get good support from Gtk#, ...
I have a file as follows:
1
3
7
12
78
...
999998
1000000
I want to find out all numbers not in the file above and put into another file like
2
4
5
6
8
9
10 (13 Replies)
Hi,
I am confused on apache service. Please advice me
There is no apache directory in my linux box. Even I cant find out httpd.conf file also.
But If browse my Hostname in Internet Explor, I can able to apache service there.
Please How it is working ..
This file is available in... (1 Reply)
Hi,
Suppose I have 3 disks c0t0d0, c0t0d1, and c0t0d2 all with the *same* VGID.
I then run:
# vgchgid /dev/rdsk/c0t0d0 /dev/rdsk/c0t0d1
(notice I *accidentally* skipped the third disk!)
How would I fix this so that all 3 disks have the same VGID again?
I'm looking for step-by-step... (7 Replies)
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
HELLO ALL,
URGENTLY NEEDED A SCRIPT TO SELECT AND DELETE LOWER AND MIXED CASE RECORDS FROM A COLUMN IN A TABLE.
FOR EXAMPLE : Table name is EMPLOYEE and the column name is CITY
and the CITY column records will be: Newyork
washington
... (1 Reply)
linux fedora core2
:) i am trying to write a script to clear, date, pwd and tty a linux termnal or konsole.. when I test the tty against $0 i am, getting a premission denied on the terminal that I am trying to printf to.. I tried using an awk command, test condition, an if then fi clause, but... (6 Replies)
VIAIDE(4) BSD Kernel Interfaces Manual VIAIDE(4)NAME
viaide -- AMD, NVIDIA and VIA IDE disk controllers driver
SYNOPSIS
viaide* at pci? dev ? function ? flags 0x0000
options PCIIDE_AMD756_ENABLEDMA
DESCRIPTION
The viaide driver supports the following IDE controllers and provides the interface with the hardware for the ata driver:
- Advanced Micro Devices AMD-756, 766, 768 and CS5536 IDE Controllers
- NVIDIA nForce, nForce2, nForce2 400, nForce3, nForce3 250, nForce4, MCP04, MCP55, MCP61, MCP65, MCP67 IDE and SATA Controllers.
- VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, VT8235, VT8237/VT8237R IDE Controllers, VT6421 Serial RAID
Controller and CX700 IDE Controller.
The 0x0002 flag forces the viaide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)NOTES
Drives on the VT6421 Serial RAID Controller can only be accessed after they have been configured into RAID or JBOD sets via its BIOS. It is
also inaptly named as it has both SATA and PATA interfaces.
BUGS
The AMD756 chip revision D2 has a bug affecting DMA (but not Ultra-DMA) modes. The workaround documented by AMD is to not use DMA on any
drive which does not support Ultra-DMA modes. This does not appear to be necessary on all drives, the PCIIDE_AMD756_ENABLEDMA option can be
used to force multiword DMA on the buggy revisions. Multiword DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4). The bug, if triggered, will cause a total system hang.
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD August 31, 2007 BSD
