9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
vb(7) Miscellaneous Information Manual vb(7)
NAME
vb, sys_attrs_vme_vba - VMEbus backplane Ethernet interface
SYNOPSIS
controller vb0 at vba0
DESCRIPTION
The VMEbus backplane (vb) interface provides access to an Ethernet network through the VMEbus backplane driver, which acts as an Ethernet
Datalink Layer driver. This interface allows VMEbus-based systems to communicate directly over the VMEbus to other VMEbus-based systems on
the same backplane, or on other Ethernet connected systems outside the backplane through a gateway node on the backplane.
Both the Tru64 UNIX and VxWorks for Alpha (Version 3.1 or higher) software support the vb driver as well as communication between these
systems on the same backplane. The Tru64 UNIX vb driver is supported on AXPvme and Alpha VME SBCs and Alpha VME 2100 systems.
The VMEbus backplane interface requires you to modify the /etc/sysconfigtab file on your AXPvme or Alpha VME system in order to configure
the vb driver and to map VMEbus windows for the system. Mapping the VMEbus windows on one node requires knowledge about every node in the
vb network.
Note
Do not modify any vme_vba kernel subsystem attributes. To configure a vb network node, you modify attributes of the vb driver (vb:) and
the system's VMEbus adapter (vba_vipvic: or vba_univ:).
See System Configuration Supplement: OEM Platforms for detailed information about the use of the vb interface on Alpha VME systems, includ-
ing the following topics: VMEbus backplane (vb) network overview Configuring vb network nodes Modifying vb driver attributes Modifying
vba_vipvic adapter attributes Modifying vba_univ adapter attributes Examples Related ioctl commands Diagnostic messages Errors
RELATED INFORMATION
Interfaces: sys_attrs_vba_vipvic(7), sys_attrs_vba_univ(7), sysconfigdb(8)
Network Administration, System Configuration Supplement: OEM Platforms delim off
vb(7)