10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
Hi,
It was happened to close my laptop without proper shutdown due to power failure with USB device connected to it. (removed the USB after shut down)
After this incident, I was not able to boot my suse linux OS.
Initial study reveals that the device is not unmounted properly and shows... (2 Replies)
Discussion started by: Prabhu V
2 Replies
2. UNIX for Dummies Questions & Answers
I am a newbie to Suse linux and was trying to configure internet on my 11.4 suse linux system . I followed a post according to which i uninstalled my NetworkManger library . Later i realised that the real reason for wireless not working on my system was that my wireless driver firmware was... (0 Replies)
Discussion started by: ihatetoregister
0 Replies
3. Solaris
Hi all,
Previously I had both opensuse 11.3 and Windows XP SP2 on my PC, there was no problem at all.I was able to access all documents in Windows from opensuse.
Now when I wanted to install solaris 10 on the same machine there were 2 problems ...
1. Windows is not accessible from solaris... (3 Replies)
Discussion started by: M.Choudhury
3 Replies
4. Filesystems, Disks and Memory
I setup a RAID 5 with 5 drives, one failed, hardware failure so I physically removed it from the raid after powering the machine off then powered it back on and my raid was still good but no 5th drive. I built a 5th drive from scratch and added it in the raid thinking the raid would go into... (0 Replies)
Discussion started by: lacakid
0 Replies
5. SuSE
Dear Experts,
i am trying to find whether the given name is file or a directory
dirp = opendir(dirname);
direntp = readdir(dirp);
if(direntp->d_type & DT_DIR)
{
printf("\n is a dirctory");
}
else
{
//dir_or_file = Mtrue;
printf("\n not a directory");
}
it always... (9 Replies)
Discussion started by: vin_pll
9 Replies
6. SuSE
hi Guys,,
Am very new to Linux OS.. This is my first experience with Linux.
I have installed linux suse 10 in my laptop.it was working fine.. suddenly after 3 days,(i was changing some options of the already installed linux) when i login, i am getting only command interface and GUI is not... (2 Replies)
Discussion started by: mac4rfree
2 Replies
7. Filesystems, Disks and Memory
Hi all!
Working on Oracle v8.1.7.0.0 with OS as Suse v8.0 Linux.
I had created LVM,linked raw devices to LVM as below:
# for binding raw devices
raw /dev/raw/raw1 /dev/oracle/sam_raw_system_251m
raw /dev/raw/raw2 /dev/oracle/sam_raw_users_26m
raw /dev/raw/raw3... (2 Replies)
Discussion started by: Amitstora
2 Replies
8. SuSE
I setup SUSE Linux 10.
I downloaded from SUSE website. A DVD version.
But I have a problem:
Please click to see the screen shots
Shot 1: (Problem is here, with Software)
http://www.vernoos.net/shot-1.jpg
Shot 2:
http://www.vernoos.net/shot-2.jpg
Shot 3:... (1 Reply)
Discussion started by: HASSELBLAD
1 Replies
9. UNIX for Dummies Questions & Answers
i got a NV11 geForce2 100/200 and suse 9.0 pro boot the kernal but then the screen
goes blank and nothing else can't install suse 9.0 pro and grabs for this problem
x will not come up at all
just the boot screen with rez and so on but once i tell it to install thats i have a nec multisync... (6 Replies)
Discussion started by: 3bumbs plumming
6 Replies
10. UNIX for Dummies Questions & Answers
i have just installed suse 8.1 on a third computer which has an Asus p4s8x with onboard NIC and sound. now, on install suse detected everything automatically with no probelm, however upon reboot the sound failed to load as well as the network card. /dev/eth* doesnt exist. i looked in the bios and... (2 Replies)
Discussion started by: norsk hedensk
2 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only non-empty, non-extended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the `primary' partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS `primary' partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
mknod(1), chown(1), mount(8), sd(4)
Linux 1992-12-17 HD(4)