9 More Discussions You Might Find Interesting
1. Solaris
Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue:
Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies
2. Solaris
Dear All,
I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface .
The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped.
But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies
3. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
4. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
5. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
6. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
root_archive(1M) System Administration Commands root_archive(1M)
NAME
root_archive - manage bootable miniroot archives
SYNOPSIS
/boot/solaris/bin/root_archive pack archive root
/boot/solaris/bin/root_archive unpack archive root
/boot/solaris/bin/root_archive packmedia solaris_image root
/boot/solaris/bin/root_archive unpackmedia solaris_image root
DESCRIPTION
The root_archive utility is used to manage bootable miniroot archives and is currently only available on x86 platforms. The utility can
pack and unpack boot/root archives in both ufs and hsfs (iso9660) format. It will always generate ufs archives.
root_archive also uses the lofi file driver to export a file as a block device (see lofi(7D)) and mount to mount or unmount file systems
and remote resources (see mount(1M)). root_archive requires the same privileges that are needed to run these commands.
SUBCOMMANDS
The root_archive command has the following subcommands:
pack archive root Pack from the image found under the root directory to the archive.
unpack archive root
Unpack from the archive to an unpacked image under the root directory.
packmedia solaris_image root
Pack the solaris image to the root directory.
unpackmedia solaris_image root
Unpack the solaris image from the root directory.
For packmedia and unpackmedia, other items that do not go into the ramdisk image are copied or uncopied (see cpio(1)) as well. Specifi-
cally, this includes all the packaging databases needed for pkgadd and the other packaging utilities to succeed which are not used in the
running and hence pruned to conserve memory.
EXAMPLES
Example 1 Unpacking the Solaris x86 install image
The following command unpacks the current Solaris image from the root directory:
# root_archive unpackmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
Where /export/nv/solarisdvd.nvx_dvd/latest represents a path to a Solaris x86 install image and /export/Boot is a directory that will be
purged or created, as necessary.
Example 2 Packing the Solaris x86 install image
The following command packs the current Solaris image to the root directory:
# root_archive packmedia
/export/nv/solarisdvd.nvx_dvd/latest /export/Boot
EXIT STATUS
The following exit values are returned:
0 The command completed successfully.
1 The command exited due to an error.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Stable |
+-----------------------------+-----------------------------+
SEE ALSO
cpio(1), bootadm(1M), mount(1M), attributes(5), lofi(7D)
SunOS 5.11 26 Sep 2005 root_archive(1M)