9 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
6. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
7. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
8. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
9. BSD
Hello All,
How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies
OCF_HEARTBEAT_ISCSI(7) OCF resource agents OCF_HEARTBEAT_ISCSI(7)
NAME
ocf_heartbeat_iscsi - Manages a local iSCSI initiator and its connections to iSCSI targets
SYNOPSIS
iscsi [start | stop | status | monitor | meta-data | validate-all]
DESCRIPTION
OCF Resource Agent for iSCSI. Add (start) or remove (stop) iSCSI targets.
SUPPORTED PARAMETERS
portal
The iSCSI portal address in the form: {ip_address|hostname}[":"port] (required, string, no default)
target
The iSCSI target IQN. (unique, required, string, no default)
discovery_type
Target discovery type. Check the open-iscsi documentation for supported discovery types. (optional, string, default sendtargets)
iscsiadm
open-iscsi administration utility binary. (optional, string, default iscsiadm)
udev
If the next resource depends on the udev creating a device then we wait until it is finished. On a normally loaded host this should be
done quickly, but you may be unlucky. If you are not using udev set this to "no", otherwise we will spin in a loop until a timeout
occurs. (optional, string, default yes)
SUPPORTED ACTIONS
This resource agent supports the following actions (operations):
start
Starts the resource. Suggested minimum timeout: 120.
stop
Stops the resource. Suggested minimum timeout: 120.
status
Performs a status check. Suggested minimum timeout: 30.
monitor
Performs a detailed status check. Suggested minimum timeout: 30. Suggested interval: 120.
validate-all
Performs a validation of the resource configuration. Suggested minimum timeout: 5.
methods
Suggested minimum timeout: 5.
meta-data
Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.
EXAMPLE
The following is an example configuration for a iscsi resource using the crm(8) shell:
primitive p_iscsi ocf:heartbeat:iscsi
params
portal=string
target=string
op monitor depth="0" timeout="30" interval="120"
SEE ALSO
http://www.linux-ha.org/wiki/iscsi_(resource_agent)
AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors)
resource-agents UNKNOWN 03/09/2014 OCF_HEARTBEAT_ISCSI(7)