10 More Discussions You Might Find Interesting
1. Solaris
I'm building a Solaris 11 OVM environment and want to configure everything to boot from our high performance SAN (no local disks). I've got everything working and the system boots nicely via an OBP configuration however I'd like to configure redundant IP interfaces within Solaris, what I'm... (4 Replies)
Discussion started by: ISCSIboot
4 Replies
2. Homework & Coursework Questions
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example?
You (accidentally?) posted in the Homework-section of the forum, where special rules apply. If... (0 Replies)
Discussion started by: spark2k06
0 Replies
3. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
4. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
5. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
6. Solaris
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies
7. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
8. Solaris
Hello,
I am trying to breakdown the cXtXdX (specifically tX) part of an iscsi device.
I know in the fibre SAN world, this tX will usually be a combination of the path to device/device WWN.
From what I understand in iscsi world it is similar, breaking down into... (0 Replies)
Discussion started by: Bashful
0 Replies
9. UNIX for Dummies Questions & Answers
:confused:Hi
This was installed on the Linux box a few weeks back by a guy that no longer works for us. All worked fine until last week. Now when we connect its just a blank screen with no icons.
I get a whole bunch of errors when starting the service too:
Tue Feb 23 14:29:45 2010
... (1 Reply)
Discussion started by: wbdevilliers
1 Replies
10. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
