9 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
6. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
7. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
8. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
9. BSD
Hello All,
How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies
ISCSI(4) BSD Kernel Interfaces Manual ISCSI(4)
NAME
iscsi -- iSCSI initiator
SYNOPSIS
To compile this driver into the kernel, place the following line in the kernel configuration file:
device iscsi
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
iscsi_load="YES"
DESCRIPTION
The iscsi subsystem provides the kernel component of an iSCSI initiator. The initiator is the iSCSI client, which connects to an iSCSI tar-
get, providing local access to a remote block device. The userland component is provided by iscsid(8) and both the kernel and userland are
configured using iscsictl(8). The iscsi subsystem is responsible for implementing the "Full Feature Phase" of the iSCSI protocol.
SYSCTL VARIABLES
The following variables are available as both sysctl(8) variables and loader(8) tunables:
kern.iscsi.ping_timeout
The number of seconds to wait for the target to respond to a NOP-Out PDU. In the event that there is no response within that time
the session gets forcibly restarted.
kern.iscsi.iscsid_timeout
The number of seconds to wait for ctld(8) to establish a session. After that time iscsi will abort and retry.
kern.iscsi.login_timeout
The number of seconds to wait for a login attempt to succeed. After that time iscsi will abort and retry.
kern.iscsi.maxtags
The maximum number of outstanding IO requests.
kern.iscsi.fail_on_disconnection
Controls the behavior after an iSCSI connection has been dropped due to network problems. When set to 1, a dropped connection causes
the iSCSI device nodes to be destroyed. After reconnecting, they will be created again. By default, the device nodes are left
intact. While the connection is down all input/output operations are suspended, to be retried after the connection is reestablished.
SEE ALSO
iscsi.conf(5), iscsictl(8), iscsid(8)
HISTORY
The iscsi subsystem first appeared in FreeBSD 10.0.
AUTHORS
The iscsi subsystem was developed by Edward Tomasz Napierala <trasz@FreeBSD.org> under sponsorship from the FreeBSD Foundation.
BSD
September 11, 2014 BSD