Login or Register to Ask a Question and Join Our Community


Solaris

How do I breakdown the Target (tx) part of a cXtXdX Iscsi device?

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris How do I breakdown the Target (tx) part of a cXtXdX Iscsi device?
# 1  
Old 05-24-2010
How do I breakdown the Target (tx) part of a cXtXdX Iscsi device?
Hello,

I am trying to breakdown the cXtXdX (specifically tX) part of an iscsi device.

I know in the fibre SAN world, this tX will usually be a combination of the path to device/device WWN.

From what I understand in iscsi world it is similar, breaking down into hba-id/initator-id/Lun-id-or-0.. is this correct?

And if so, how do I seperate these out? How do I knwo which is the hba-id and son on?

Thank you,
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. Linux

How to boot iSCSI target from console linux?

I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies

2. HP-UX

Unable to delete iscsi target

Hi Please can someone give me a hint on this, when I list the targets, I see two o them: #iscsiutil -p Operational Target Information ------------------------------ Target # 1 ----------- Target Name : iqn.1992-08.com.netapp:sn.142241859 Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies

3. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

4. UNIX for Advanced & Expert Users

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies

5. Solaris

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies

6. UNIX for Advanced & Expert Users

LTO2 tape drive as iSCSI target

I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies

7. Solaris

Iscsi - target + initiator on the same host.

Hi all iscsiadm / iscsitadm. Ive created two devices on a host. # iscsitadm list target Target: 1-disk0 iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0 Connections: 1 Target: 1-disk1 iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies

8. Solaris

iscsi device on solaris 10 (x64)

Hello! I have several disks discovered using iscsi protocol. There disks are represented in OS like c2txd0 . logs: Is it possible to change drive path, for example, from c2t6d0 to c2t7d0? It's important for me because I have to install oracle RAC on RAW devices. NIck (0 Replies)
Discussion started by: skelet
0 Replies
Login or Register to Ask a Question