10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
2. Solaris
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies
3. Solaris
Hello all,
I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0.
This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help.
Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
4. Solaris
Hi all,
I have been administrating large backup environments for quite some time now, but I have never seen the types of errors I'm getting for a client I have in Asia, so I humbly appeal to your expertise in order to fix things.
Set up: StreamLine 8500 library connected to a Solaris... (7 Replies)
Discussion started by: dilibau
7 Replies
5. Solaris
(Disclaimer: I put this in the "dummies" section because I am a UNIX noob and I'm not really sure what I'm doing so I felt like it belonged here. If it belongs in the Solaris section I can delete this and post it there:b:)
I was handed over an Oracle SPARC T3-1 machine at work, with 8 physical... (15 Replies)
Discussion started by: bstring
15 Replies
6. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
7. Solaris
I want to configure my Network card. On solaris 9 i386.
How to know the good Network device. I use prtconf
to display the device list. I'm searching the device name.
Like ifconfig device_name plumb
thanks you (2 Replies)
Discussion started by: simquest
2 Replies
8. Solaris
On prior versions to solaris 10 when I want to add/change the IP address of an interface I will use this command.
ifconfig eri0 down
ifconfig eri0 192.xxx.xxx.xxx netmask 255.xxx.xxx.xxx up
then change /etc/hosts so that /etc/hostname.eri0 picks up on the correct IP.
I strange thing... (2 Replies)
Discussion started by: sparcguy
2 Replies
9. IP Networking
Hi guys,
I have set up multiple virtual FTP servers on a server through one physical NIC. I believe there are to ways; setting logical or alias ip's. I would like to know what is the difference between setting up a logical ip or setting up an alias ip to a physical network interface? Some links to... (5 Replies)
Discussion started by: zaff
5 Replies
10. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies