10 More Discussions You Might Find Interesting
1. HP-UX
Is there one? If so where can it be found? I have the 10.20 CD set but I don't think that there's an iSCSI initiator on there.
Thank you
Dave (0 Replies)
Discussion started by: perdrix
0 Replies
2. Shell Programming and Scripting
Hi All,
Need to connect to target host and execute a command and connect back to source host to continue with next set of command execution.
Is there a utility/command using which we can connect to target host ?
Please suggest.
Note: Netezza database is instaled on Linux server. ... (4 Replies)
Discussion started by: Nagaraja Akkiva
4 Replies
3. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
4. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
5. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
6. UNIX for Dummies Questions & Answers
hi all,
i'm new here and i have a question,
i wanted to know, what should happen if i delete a LUN that is already mounted on one of my initiators.
thanks! (3 Replies)
Discussion started by: slavash
3 Replies
7. Solaris
I have a Sun Blade 2500 with SUN 5.9 OS installed.
I have configured ISCSI SAN and one of my Red Hat OS can accessed/mount the ISCSI SAN disk
Now i want to access/mount another ISCSI SAN disk on SUN solaris. Is that possible ?
Thanks (1 Reply)
Discussion started by: z_haseeb
1 Replies
8. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
9. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
10. Solaris
Hello,
I am trying to breakdown the cXtXdX (specifically tX) part of an iscsi device.
I know in the fibre SAN world, this tX will usually be a combination of the path to device/device WWN.
From what I understand in iscsi world it is similar, breaking down into... (0 Replies)
Discussion started by: Bashful
0 Replies
ISCSICTL(8) BSD System Manager's Manual ISCSICTL(8)
NAME
iscsictl -- iSCSI initiator management utility
SYNOPSIS
iscsictl -A -p portal -t target [-u user -s secret]
iscsictl -A -d discovery-host [-u user -s secret]
iscsictl -A -a [-c path]
iscsictl -A -n nickname [-c path]
iscsictl -M -i session-id [-p portal] [-t target] [-u user] [-s secret]
iscsictl -M -i session-id [-n nickname [-c path]]
iscsictl -R [-p portal] [-t target]
iscsictl -R -a
iscsictl -R -n nickname [-c path]
iscsictl -L [-v]
DESCRIPTION
The iscsictl utility is used to configure the iSCSI initiator.
The following options are available:
-A Add session.
-M Modify session.
-R Remove session.
-L List sessions.
-a When adding, add all sessions defined in the configuration file. When removing, remove all currently established sessions.
-c Path to the configuration file. The default is /etc/iscsi.conf.
-d Target host name or address used for SendTargets discovery. When used, it will add a temporary discovery session. After discovery is
done, sessions will be added for each discovered target, and the temporary discovery session will be removed.
-i Session ID, as displayed by iscsictl -v.
-n The "nickname" of session defined in the configuration file.
-p Target portal - host name or address - for statically defined targets.
-s CHAP secret.
-t Target name.
-u CHAP login.
-v Verbose mode.
Certain parameters are necessary when adding a session. One can specify these either via command line (using the -t, -p, -u, and -s
options), or configuration file (using the -a or -n options). Some functionality - for example mutual CHAP - is available only via configu-
ration file.
Since connecting to the target is performed in background, non-zero exit status does not mean that the session was successfully established.
Use iscsictl -L to check the connection status.
Note that in order for the iSCSI initiator to be able to connect to a target, the iscsid(8) daemon must be running.
Also note that FreeBSD currently supports two different initiators: the old one, iscsi_initiator(4), with its control utility iscontrol(8),
and the new one, iscsi(4), with iscsictl and iscsid(8). The only thing the two have in common is the configuration file, iscsi.conf(5).
FILES
/etc/iscsi.conf iSCSI initiator configuration file.
EXIT STATUS
The iscsictl utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
Attach to target iqn.2012-06.com.example:target0, served by 192.168.1.1:
iscsictl -A -t iqn.2012-06.com.example:target0 -p 192.168.1.1
Disconnect all iSCSI sessions:
iscsictl -Ra
SEE ALSO
iscsi(4), iscsi.conf(5), iscsid(8)
HISTORY
The iscsictl command appeared in FreeBSD 10.0.
AUTHORS
The iscsictl utility was developed by Edward Tomasz Napierala <trasz@FreeBSD.org> under sponsorship from the FreeBSD Foundation.
BSD
September 12, 2014 BSD