10 More Discussions You Might Find Interesting
1. Red Hat
Hi Expert,
I'm having grub problem here:
grub> root
(hd0,0): Filesystem type is ext2
grub> setup
Error 11 : Unrecognized Device String
I try install boot loader follow the instruction from 26.2. Booting into Rescue Mode
It says : select Continue, it attempts to mount your file... (4 Replies)
Discussion started by: justbow
4 Replies
2. Shell Programming and Scripting
is there a better way to do this:
head -c 10000k /var/dump.log | head -c 6000k
unfortunately, the "-c" option is not available on sun solaris. so i'm looking at "dd". but i dont know how to use it to achieve the same exact goal as the above head command.
this needs to work on both solaris... (5 Replies)
Discussion started by: SkySmart
5 Replies
3. Shell Programming and Scripting
hello,
suppose, entered input is of 1-40 bytes, i need it to be converted to 40 bytes exactly.
example: if i have entered my name anywhere between 1-40 i want it to be stored with 40 bytes exactly.
enter your name:
donald duck (this is of 11 bytes)
expected is as below - display 11... (3 Replies)
Discussion started by: shravan.300
3 Replies
4. UNIX for Dummies Questions & Answers
Hello guys. I really hope someone will help me with this one..
So, I have to write this script who:
- creates a file home/student/vmdisk of 10 mb
- formats that file to ext3
- mounts that partition to /mnt/partition
- creates a file /mnt/partition/data. In this file, there will... (1 Reply)
Discussion started by: razolo13
1 Replies
5. Programming
Hi,
If I want to copy a 1024 byte data stream in to the target location in 3-bytes chunk, I guess I can use the following script.
dd bs=1024 count=3 if=/src of=/dest
But, I would like to know, how to do it via a C program. I have tried this with memcpy(), that did not help. (3 Replies)
Discussion started by: royalibrahim
3 Replies
6. Shell Programming and Scripting
While running script I am getting an error like
Few lines in data are not being processed.
After googling it I came to know that adding such line would give some memory to it
ini_set("memory_limit","64M");
my input file size is 1 GB.
Is that memory limit is based on RAM we have on... (1 Reply)
Discussion started by: elamurugu
1 Replies
7. Programming
What is the easiest way to inspect the bytes stored in a file?
Ideally, If my file was 10 bytes each of which had only the high bit set, I'd be able to browse for it and get output like this:
01 - 10000000
02 - 10000000
03 - 10000000
04 - 10000000
05 - 10000000
06 - 10000000
07 -... (7 Replies)
Discussion started by: sneakyimp
7 Replies
8. UNIX for Dummies Questions & Answers
Hi,
How do I check for the total bytes of character used by a file?
Can I used a od command to check?
Thanks. (1 Reply)
Discussion started by: user50210
1 Replies
9. Shell Programming and Scripting
Hi all,
Does anybody know or guide me on how to remove the first N bytes and the last N bytes from a binary file? Is there any AWK or SED or any command that I can use to achieve this?
Your help is greatly appreciated!!
Best Regards,
Naveen. (1 Reply)
Discussion started by: naveendronavall
1 Replies
10. UNIX for Dummies Questions & Answers
:mad: I did this the other day but one of my support personnel removed my history so i could call it back up to remeber the exact command since i am air-headed at times. I am trying to take a 30 MEG file off the system and drop it to tape then i want to make the file go back to being 0 bytes so... (1 Reply)
Discussion started by: JackieRyan26
1 Replies
ATF-SH(1) BSD General Commands Manual ATF-SH(1)
NAME
atf-sh [-s shell] -- interpreter for shell-based test programs
SYNOPSIS
atf-sh script
DESCRIPTION
atf-sh is an interpreter that runs the test program given in script after loading the atf-sh(3) library.
atf-sh is not a real interpreter though: it is just a wrapper around the system-wide shell defined by ATF_SHELL. atf-sh executes the inter-
preter, loads the atf-sh(3) library and then runs the script. You must consider atf-sh to be a POSIX shell by default and thus should not
use any non-standard extensions.
The following options are available:
-s shell Specifies the shell to use instead of the value provided by ATF_SHELL.
ENVIRONMENT
ATF_LIBEXECDIR Overrides the builtin directory where atf-sh is located. Should not be overridden other than for testing purposes.
ATF_PKGDATADIR Overrides the builtin directory where libatf-sh.subr is located. Should not be overridden other than for testing purposes.
ATF_SHELL Path to the system shell to be used in the generated scripts. Scripts must not rely on this variable being set to select a
specific interpreter.
EXAMPLES
Scripts using atf-sh(3) should start with:
#! /usr/bin/env atf-sh
Alternatively, if you want to explicitly choose a shell interpreter, you cannot rely on env(1) to find atf-sh. Instead, you have to hardcode
the path to atf-sh in the script and then use the -s option afterwards as a single parameter:
#! /path/to/bin/atf-sh -s/bin/bash
ENVIRONMENT
ATF_SHELL Path to the system shell to be used in the generated scripts.
SEE ALSO
atf-sh(3)
BSD
September 27, 2014 BSD