IRQ conflict between USB and NIC SCO 5.0.7


 
Thread Tools Search this Thread
Operating Systems SCO IRQ conflict between USB and NIC SCO 5.0.7
# 1  
Old 09-13-2008
IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential for our system please provide a solution in this regards.
I have loaded the maintainence pack -5 CD in the server.
The BIOS doenot have settings for setting the IRQ's.
Thanks

Last edited by vikramviky; 09-18-2008 at 12:16 PM..
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. SCO

Usb Flash in SCO UNIX 5.0.6

hi How can I use my USB Flash memory in Sco 5.0.6 tanks (1 Reply)
Discussion started by: moein.mojtaba
1 Replies

2. SCO

USB Printing for SCO UNIX OpenServer 5.0.7

Years ago I set up USB printing for SCO UNIX OpenServer 5.0.7 for a client--but I've misplaced my notes on how to do this! Maintenance Pack 5 is installed. I need step-by-step instructions to proceed. I've searched the SCO Knowledge Base site and found nothing there or elsewhere on the Web. (3 Replies)
Discussion started by: Transpower
3 Replies

3. SCO

Install NIC on SCO openserver 5.0.2

Hi I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question: PCI BUS# DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies

4. SCO

SCO 6 + Virtualbox 2 == no NIC

Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack... (1 Reply)
Discussion started by: dalek
1 Replies

5. UNIX for Dummies Questions & Answers

SCO 5.0.5 & USB flash drive

Can someone help me with instructions on how to access a USB flash drive in SCO Unix 5.0.5? I need to copy ASCII text files that have been zipped onto the USB drive for transfer to a Windows computer. (0 Replies)
Discussion started by: jlodata
0 Replies

6. Programming

ncurses and usb library conflict

Hi I am writing a piece of code using gcc-3.4.4 which uses usb library (-lusb) to interact with a small robot, getting inputs from sensors and sending commands back to motors. Now my problem is that when I use ncurses library in my code to get use of keyboard functionalities, the usb inputs do... (1 Reply)
Discussion started by: omoallemi
1 Replies

7. SCO

an usb falsh disk under sco?

is it possible to access an usb flash disk under sco unixware 7.11? and how to do? any help is apreciated (0 Replies)
Discussion started by: nabil_boussetta
0 Replies

8. SCO

in sco unix 5.0.6 ,can i use the USB?

I have a USB,can i use it in the sco unix 5.0.6? (1 Reply)
Discussion started by: fresh
1 Replies

9. UNIX for Dummies Questions & Answers

usb - deleting (irq)

FreeBSD 4.5 i installed my sound drivers (which are onboard) with the following lines in my kernel device pcm options PNPBIOS then cd /dev sh MAKEDEV snd0 output from cat /dev/sndstat show the devicedriver (correct one) ok this works nice untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies

10. UNIX for Dummies Questions & Answers

Installing nic on sco 5.0.5

How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
Login or Register to Ask a Question
UMCS(4) 						   BSD Kernel Interfaces Manual 						   UMCS(4)

NAME
umcs -- USB support for serial adapters based on the MCS7820 and MCS7840 chips SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device usb device ucom device umcs Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): umcs_load="YES" DESCRIPTION
The umcs driver provides support for various multiport serial adapters based on the MosCom MCS7820 and MCS7840 chips. They are 2- or 4-port adapters with full-featured 16550-compatible UARTs and very flexible baud generators. Also, these chips support RS422/RS485 and IrDA opera- tions. The device is accessed through the ucom(4) driver which makes it behave like a tty(4). Different ports on device are presented as sub-units, like /dev/ttyU0.1 and /dev/ttyU0.2. HARDWARE
The umcs driver was tested on the following adapters: o ST Lab U-360 two-port serial USB adapter o ST Lab U-400 four-port serial USB adapter SEE ALSO
tty(4), ucom(4), usb(4) HISTORY
The umcs driver appeared in ports since December of 2010. AUTHORS
The umcs driver was written by Lev Serebryakov <lev@FreeBSD.org>. BUGS
This driver doesn't support access to any fine tunes of chip, like RS522/RS485 mode, non-standard baudrates, etc. BSD
February 25, 2012 BSD