10 More Discussions You Might Find Interesting
1. SCO
hi
How can I use my USB Flash memory in Sco 5.0.6
tanks (1 Reply)
Discussion started by: moein.mojtaba
1 Replies
2. SCO
Years ago I set up USB printing for SCO UNIX OpenServer 5.0.7 for a client--but I've misplaced my notes on how to do this! Maintenance Pack 5 is installed. I need step-by-step instructions to proceed. I've searched the SCO Knowledge Base site and found nothing there or elsewhere on the Web. (3 Replies)
Discussion started by: Transpower
3 Replies
3. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
4. SCO
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack... (1 Reply)
Discussion started by: dalek
1 Replies
5. UNIX for Dummies Questions & Answers
Can someone help me with instructions on how to access a USB flash drive in SCO Unix 5.0.5? I need to copy ASCII text files that have been zipped onto the USB drive for transfer to a Windows computer. (0 Replies)
Discussion started by: jlodata
0 Replies
6. Programming
Hi
I am writing a piece of code using gcc-3.4.4 which uses usb library (-lusb) to interact with a small robot, getting inputs from sensors and sending commands back to motors.
Now my problem is that when I use ncurses library in my code to get use of keyboard functionalities, the usb inputs do... (1 Reply)
Discussion started by: omoallemi
1 Replies
7. SCO
is it possible to access an usb flash disk under sco unixware 7.11?
and how to do?
any help is apreciated (0 Replies)
Discussion started by: nabil_boussetta
0 Replies
8. SCO
I have a USB,can i use it in the sco unix 5.0.6? (1 Reply)
Discussion started by: fresh
1 Replies
9. UNIX for Dummies Questions & Answers
FreeBSD 4.5
i installed my sound drivers (which are onboard) with the following lines in my kernel
device pcm
options PNPBIOS
then cd /dev
sh MAKEDEV snd0
output from cat /dev/sndstat show the devicedriver (correct one)
ok this works nice
untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies
10. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
UDAV(4) BSD Kernel Interfaces Manual UDAV(4)
NAME
udav -- Davicom DM9601 USB Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device ehci
device uhci
device ohci
device usb
device miibus
device udav
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_udav_load="YES"
HARDWARE
The udav driver supports the following adapters:
o Corega FEther USB-TXC
o ShanTou ST268 USB NIC
DESCRIPTION
The udav driver provides support for USB Ethernet adapters based on the Davicom DM9601 chipset.
For more information on configuring this device, see ifconfig(8).
SEE ALSO
altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), usb(4), ifconfig(8)
Davicom DM9601 data sheet, http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf.
HISTORY
The udav device driver first appeared in NetBSD 2.0.
AUTHORS
The udav driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
July 16, 2005 BSD