IRQ conflict between USB and NIC SCO 5.0.7

10 More Discussions You Might Find Interesting

1. SCO

Usb Flash in SCO UNIX 5.0.6

hi How can I use my USB Flash memory in Sco 5.0.6 tanks

2. SCO

USB Printing for SCO UNIX OpenServer 5.0.7

Years ago I set up USB printing for SCO UNIX OpenServer 5.0.7 for a client--but I've misplaced my notes on how to do this! Maintenance Pack 5 is installed. I need step-by-step instructions to proceed. I've searched the SCO Knowledge Base site and found nothing there or elsewhere on the Web.

3. SCO

Install NIC on SCO openserver 5.0.2

Hi I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question: PCI BUS# DEVICE#...

4. SCO

SCO 6 + Virtualbox 2 == no NIC

Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack...

5. UNIX for Dummies Questions & Answers

SCO 5.0.5 & USB flash drive

Can someone help me with instructions on how to access a USB flash drive in SCO Unix 5.0.5? I need to copy ASCII text files that have been zipped onto the USB drive for transfer to a Windows computer.

6. Programming

ncurses and usb library conflict

Hi I am writing a piece of code using gcc-3.4.4 which uses usb library (-lusb) to interact with a small robot, getting inputs from sensors and sending commands back to motors. Now my problem is that when I use ncurses library in my code to get use of keyboard functionalities, the usb inputs do...

7. SCO

an usb falsh disk under sco?

is it possible to access an usb flash disk under sco unixware 7.11? and how to do? any help is apreciated

8. SCO

in sco unix 5.0.6 ,can i use the USB?

I have a USB,can i use it in the sco unix 5.0.6?

9. UNIX for Dummies Questions & Answers

usb - deleting (irq)

FreeBSD 4.5 i installed my sound drivers (which are onboard) with the following lines in my kernel device pcm options PNPBIOS then cd /dev sh MAKEDEV snd0 output from cat /dev/sndstat show the devicedriver (correct one) ok this works nice untill i enter my kde and want to play a...

10. UNIX for Dummies Questions & Answers

Installing nic on sco 5.0.5

How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused:

LEARN ABOUT FREEBSD

usb_template

USB_TEMPLATE(4) 					   BSD Kernel Interfaces Manual 					   USB_TEMPLATE(4)

NAME

     usb_template -- USB templates

SYNOPSIS

     To compile this module into the kernel, place the following line in your kernel configuration file:

	   device usb_template

     To load the module at boot time, place the following line in loader.conf(5):

	   usb_template_load="YES"

DESCRIPTION

     The usb_template module implements various USB templates that are needed when programming an USB device side driver.  A USB template consists
     of an USB device descriptor, one or more USB configuration descriptors, one or more USB interface descriptors, one or more USB endpoint
     descriptors, USB strings and additional USB descriptors.  The USB template module currently has templates for USB Mass Storage, USB CDC Eth-
     ernet and Message Transfer Protocol.  USB templates are currently selected using the "hw.usb.template" sysctl.  The "hw.usb.template" value
     can be changed at any time, but will not have any effect until the USB device has been re-enumerated.

SEE ALSO

     usb(4)

STANDARDS

     The usb_template module complies to the USB 1.0, 2.0 and 3.0 standard.

HISTORY

     The usb_template module was written by Hans Petter Selasky <hselasky@FreeBSD.org>.

BSD
								  March 18, 2014							       BSD

SCO