8 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
2. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
3. Solaris
Hi all,
OS is Solaros 10 Sparc
While doing Netbackup upgradation to 7.5 , the server was asked to reboot.
But then it came up in single user mode,
and after I typed format command it showed some disk error.
bash-3.00# format
Searching for disks...WARNING:... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
4. Solaris
Hi, I have a firewire external hard drive that I've been using on a Mac but now want to use on my desktop computer that runs on Solaris 10, but when I plug it into the firewire port, nothing happens. I just assumed that it would mount automatically like a USB device but it doesn't. Can someone... (7 Replies)
Discussion started by: Breanne
7 Replies
5. Shell Programming and Scripting
Hello!
I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create:
/dev/sda1 --> One big partition (minus (2*size of memory) for swap)
/dev/sda2 --> Swap partition... (1 Reply)
Discussion started by: pug123
1 Replies
6. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
7. UNIX for Dummies Questions & Answers
Hi there!
I received the following error message
The hard disk at channel 2, target 1 had a soft error.
The output of a system check reveiled the following (see entry <2,1> ):
SWXCR xcr0 error counters:
RAID Array 200 Controller Family Information Utility V1.03... (1 Reply)
Discussion started by: Ivo
1 Replies
8. UNIX for Dummies Questions & Answers
Hello All,
I have a laptop running windows 2000 and I have a External Firewire Hard Disk of 60 GB. Now my question is, " Is it possible to install Solaris 8 on this external Firewire Hard Disk". When I tried installing, It did not find the external Firewire Disk, the only partition information,... (1 Reply)
Discussion started by: sanjay92
1 Replies
volrootmir(8) System Manager's Manual volrootmir(8)
NAME
volrootmir - Mirror areas necessary for booting to a new disk
SYNOPSIS
/usr/sbin/volrootmir [-a] [nconfig=count] target_disk [swap=target_partition]
OPTIONS
Specifies that all volumes on the system disk be mirrored, not just the root and swap volumes, rootvol and swapvol.
DESCRIPTION
The volrootmir script causes a mirror copy of areas of the root disk involved in booting to be made on the specified target disk.
When used without the -a option, volrootmir adds mirrors of the root and swap volumes and allocates them on the new disk. In addition, all
disk regions required for booting are set up and partitions for the new volume mirrors are created.
When used with the -a option, volrootmir mirrors all in-use partitions on the system disk.
To mirror a swap volume that is on a separate disk from the root volume, the swap attribute must be used to specify a separate target for
the swap mirror.
The target disk(s) must be at least as large as the sum of the sizes of rootvol and swapvol. Also, the physical disk should not have any
disk partition in use.
This script can be called from the voldiskadm menus by choosing the Mirror volumes on a disk operation.
ATTRIBUTES
Specifies the number of log copies and copies of the configuration database, for example, nconfig=2. Specifies that the swap volume,
swapvol, be mirrored on a separate disk, as specified by target_partition.
EXAMPLES
The following command mirrors the rootvol and swapvol volumes onto the target disk, dsk3. This command will fail if swapvol is on a differ-
ent disk from rootvol.
# volrootmir dsk3 The following command mirrors rootvol, swapvol, and any other volumes on the root disk onto the target disk, dsk3.
This command will fail if swapvol is on a different disk from rootvol.
# volrootmir -a dsk3 The following command mirrors rootvol on disk dsk3, swapvol onto partition dsk7d, and any other volumes on the
root disk onto disk dsk3. This command will fail if swapvol is on the same disk as rootvol.
# volrootmir -a dsk3 swap=dsk7d The following command mirrors rootvol onto disk dsk3 and swapvol onto partition dsk7d. This command
will fail if swapvol is on the same disk as rootvol.
# volrootmir dsk3 swap=dsk7d
SEE ALSO
volintro(8), voldiskadm(8)
volrootmir(8)