Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

urtw(4) [netbsd man page]

URTW(4) 						   BSD Kernel Interfaces Manual 						   URTW(4)

NAME
urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: urtw* at uhub? port ? DESCRIPTION
The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L. urtw supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on config- uring this device, see ifconfig(8). HARDWARE
The urtw driver supports Realtek RTL8187B/L based wireless network devices, including: Card Radio Bus Belkin F5D7050E RTL8225 USB Linksys WUSB54GCv2 RTL8225 USB Netgear WG111v2 RTL8225 USB Netgear WG111v3 RTL8225 USB Safehome WLG-1500SMA5 RTL8225 USB Shuttle XPC Accessory PN20 RTL8225 USB Sitecom WL168v1 RTL8225 USB Sitecom WL168v4 RTL8225 USB SureCom EP-9001-g(2A) RTL8225 USB TRENDnet TEW-424UB V3.xR RTL8225 USB EXAMPLES
ifconfig.if(5) example configures urtw0 to join whatever network is available on boot, using WEP key ``0x1deadbeef1'', channel 11, obtaining an IP address using DHCP: nwkey 0x1deadbeef1 chan 11 dhcp Configure urtw0 to join network ``my_net'' using WPA with passphrase ``my_passphrase'': # ifconfig urtw0 nwid my_net wpakey my_passphrase Join an existing BSS network, ``my_net'': # ifconfig urtw0 192.168.1.1 netmask 0xffffff00 nwid my_net SEE ALSO
arp(4), netintro(4), usb(4), ifconfig.if(5), wpa_supplicant.conf(5), ifconfig(8), wpa_supplicant(8) Realtek, http://www.realtek.com.tw. HISTORY
The urtw device driver first appeared in FreeBSD 8.0. AUTHORS
The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>. BSD
October 17, 2009 BSD

Check Out this Related Man Page

URTW(4) 						   BSD Kernel Interfaces Manual 						   URTW(4)

NAME
urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device ehci device uhci device ohci device usb device urtw device wlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_urtw_load="YES" DESCRIPTION
The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L. urtw supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on config- uring this device, see ifconfig(8). HARDWARE
The urtw driver supports Realtek RTL8187B/L based wireless network devices, including: Card Radio Bus Belkin F5D7050E RTL8225 USB Linksys WUSB54GCv2 RTL8225 USB Netgear WG111v2 RTL8225 USB Netgear WG111v3 RTL8225 USB Safehome WLG-1500SMA5 RTL8225 USB Shuttle XPC Accessory PN20 RTL8225 USB Sitecom WL168v1 RTL8225 USB Sitecom WL168v4 RTL8225 USB SureCom EP-9001-g(2A) RTL8225 USB TRENDnet TEW-424UB V3.xR RTL8225 USB EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev urtw0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev urtw0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev urtw0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up SEE ALSO
intro(4), netintro(4), usb(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8) Realtek, http://www.realtek.com.tw. HISTORY
The urtw device driver first appeared in FreeBSD 8.0. AUTHORS
The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>. BSD
October 17, 2009 BSD
Man Page