👤
Home Man
Search
Today's Posts
Register

Linux & Unix Commands - Search Man Pages
Man Page or Keyword Search:
Select Section of Man Page:
Select Man Page Repository:

NetBSD 6.1.5 - man page for gre (netbsd section 4)

GRE(4)				   BSD Kernel Interfaces Manual 			   GRE(4)

NAME
     gre -- encapsulating network device

SYNOPSIS
     pseudo-device gre

DESCRIPTION
     The gre network interface pseudo device encapsulates datagrams into IP.  These encapsulated
     datagrams are routed to a destination host, where they are decapsulated and further routed
     to their final destination.  The ``tunnel'' appears to the inner datagrams as one hop.

     gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy
     subcommands.

     This driver currently supports the following modes of operation:

     GRE encapsulation (IP protocol number 47)
	  Encapsulated datagrams are prepended an outer datagram and a GRE header.  The GRE
	  header specifies the type of the encapsulated datagram and thus allows for tunneling
	  other protocols than IP like e.g. AppleTalk.	GRE mode is also the default tunnel mode
	  on Cisco routers.  This is also the default mode of operation of the greX interfaces.

     GRE in UDP encapsulation
	  Encapsulated datagrams are prepended a GRE header, and then they are sent over a UDP
	  socket.  Userland may create the socket and ``delegate'' it to the kernel using the
	  GRESSOCK ioctl(2).  If userland does not supply a socket, then the kernel will create
	  one using the addresses and ports supplied by ioctl(2)s SIOCSLIFPHYADDR, GRESADDRD,
	  and/or GRESADDRS.

     MOBILE encapsulation (IP protocol number 55)
	  Datagrams are encapsulated into IP, but with a shorter encapsulation.  The original IP
	  header is modified and the modifications are inserted between the so modified header
	  and the original payload.  Like gif(4), only for IP in IP encapsulation.

     The greX interfaces support a number of ioctl(2)s, such as:

     GRESADDRS:
	  Set the IP address of the local tunnel end.  This is the source address set by or dis-
	  played by ifconfig for the greX interface.

     GRESADDRD:
	  Set the IP address of the remote tunnel end.	This is the destination address set by or
	  displayed by ifconfig for the greX interface.

     GREGADDRS:
	  Query the IP address that is set for the local tunnel end.  This is the address the
	  encapsulation header carries as local address (i.e. the real address of the tunnel
	  start point.)

     GREGADDRD:
	  Query the IP address that is set for the remote tunnel end.  This is the address the
	  encapsulated packets are sent to (i.e. the real address of the remote tunnel endpoint.)

     GRESPROTO:
	  Set the operation mode to the specified IP protocol value.  The protocol is passed to
	  the interface in (struct ifreq)->ifr_flags.  The operation mode can also be given as

	  link0 link2
		    IPPROTO_UDP

	  link0 -link2
		    IPPROTO_GRE

	  -link0 -link2
		    IPPROTO_MOBILE

	  to ifconfig(8).

     GREGPROTO:
	  Query operation mode.

     GRESSOCK:
	  Delegate a socket from userland to a tunnel interface in UDP encapsulation mode.  The
	  file descriptor for the socket is passed in (struct ifreq)->ifr_value.

     Note that the IP addresses of the tunnel endpoints may be the same as the ones defined with
     ifconfig(8) for the interface (as if IP is encapsulated), but need not be, as e.g. when
     encapsulating AppleTalk.

EXAMPLES
   Example 1: Basic GRE tunneling
     Configuration example:

     Host X-- Router A	--------------tunnel---------- Router D ----Host E
	       |					  |
		\					 /
		 +----- Router B ----- Router C --------+

     On Router A (NetBSD):

	# route add default B
	# ifconfig greN create
	# ifconfig greN A D netmask 0xffffffff linkX up
	# ifconfig greN tunnel A D
	# route add E D

     On Router D (Cisco):

	Interface TunnelX
	 ip unnumbered D   ! e.g. address from Ethernet interface
	 tunnel source D   ! e.g. address from Ethernet interface
	 tunnel destination A
	ip route C <some interface and mask>
	ip route A mask C
	ip route X mask tunnelX

     or on Router D (NetBSD):

	# route add default C
	# ifconfig greN create
	# ifconfig greN D A
	# ifconfig tunnel greN D A

     If all goes well, you should see packets flowing ;-)

     If you want to reach Router A over the tunnel (from Router D (Cisco)), then you have to have
     an alias on Router A for e.g. the Ethernet interface like:

	  ifconfig <etherif> alias Y

     and on the Cisco

	  ip route Y mask tunnelX

   Example 2: Linking private subnets
     A similar setup can be used to create a link between two private networks (for example in
     the 192.168 subnet) over the Internet:

     192.168.1.* --- Router A  -------tunnel-------- Router B --- 192.168.2.*
			\			       /
			 \			      /
			   +----- the Internet ------+

     Assuming Router A has the (external) IP address A and the internal address 192.168.1.1,
     while Router B has external address B and internal address 192.168.2.1, the following com-
     mands will configure the tunnel:

     On Router A:

	# ifconfig greN create
	# ifconfig greN 192.168.1.1 192.168.2.1
	# ifconfig greN tunnel A B
	# route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1

     On Router B:

	# ifconfig greN create
	# ifconfig greN 192.168.2.1 192.168.1.1
	# ifconfig greN tunnel B A
	# route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1

   Example 3: Encapsulating GRE in UDP
     To setup the same tunnel as above, but using GRE in UDP encapsulation instead of GRE encap-
     sulation, set flags link0 and link2, and specify source and destination UDP ports.

     On Router A:

	# ifconfig greN create
	# ifconfig greN link0 link2
	# ifconfig greN 192.168.1.1 192.168.2.1
	# ifconfig greN tunnel A,port-A B,port-B
	# route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1

     On Router B:

	# ifconfig greN create
	# ifconfig greN link0 link2
	# ifconfig greN 192.168.2.1 192.168.1.1
	# ifconfig greN tunnel B,port-B A,port-A
	# route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1

   Example 4: Realizing IPv6 connectivity
     Along these lines, you can use GRE tunnels to interconnect two IPv6 networks over an IPv4
     infrastructure, or to hook up to the IPv6 internet via an IPv4 tunnel to a Cisco router.

     2001:db8:1::/64 -- NetBSD A  ---- Tunnel ---- Cisco B --- IPv6 Internet
			\			       /
			 \			      /
			  +------ the Internet ------+

     The example will use the following addressing:

     NetBSD  A has the IPv4 address A and the IPv6 address 2001:db8:1::1 (connects to internal
	     network 2001:db8:1::/64).

     Cisco B has external IPv4 address B.

     All the IPv6 internet world is behind B, so A wants to route 0::0/0 (the IPv6 default route)
	     into the tunnel.

     The GRE tunnel will use a transit network: 2001:db8:ffff::1/64 on the NetBSD side, and
	     ::2/64 on the Cisco side.

     Then the following commands will configure the tunnel:

     On Router A (NetBSD):

	# ifconfig greN create
	# ifconfig greN inet6 2001:db8:ffff::1/64
	# ifconfig greN tunnel A B
	# route add -inet6 2001:db8:ffff::/64 2001:db8:ffff::2 -ifp greN
	# route add -inet6 0::0/0 2001:db8:ffff::2 -ifp greN

     On Router B (Cisco):

	Interface TunnelX
	  tunnel mode gre ip
	  ipv6 address 2001:db8:ffff::2/64   ! transfer network
	  tunnel source B		     ! e.g. address from LAN interface
	  tunnel destination A		     ! where the tunnel is connected to
	ipv6 route 2001:db8::/64 TunnelX     ! route this network through tunnel

NOTES
     The MTU of greX interfaces is set to 1476 by default to match the value used by Cisco
     routers.  This may not be an optimal value, depending on the link between the two tunnel
     endpoints.  It can be adjusted via ifconfig(8).

     There needs to be a route to the decapsulating host that does not run over the tunnel, as
     this would be a loop.  (This is not relevant for IPv6-over-IPv4 tunnels, of course.)

     In order to tell ifconfig(8) to actually mark the interface as up, the keyword ``up'' must
     be given last on its command line.

     The kernel must be set to forward datagrams by either option GATEWAY in the kernel config
     file or by issuing the appropriate option to sysctl(8).

SEE ALSO
     atalk(4), gif(4), inet(4), ip(4), netintro(4), options(4), protocols(5), ifconfig(8),
     sysctl(8)

     A description of GRE encapsulation can be found in RFC 1701 and RFC 1702.

     A description of MOBILE encapsulation can be found in RFC 2004.

AUTHORS
     Heiko W.Rupp <hwr@pilhuhn.de>
     David Young <dyoung@NetBSD.org> (GRE in UDP encapsulation, bug fixes)

BUGS
     The GRE RFCs are not yet fully implemented (no GRE options).

     The MOBILE encapsulation appears to have been broken since it was first added to NetBSD,
     until August 2006.  It is known to interoperate with another gre in MOBILE mode, however, it
     has not been tested for interoperability with any other implementation of RFC 2004.

     The NetBSD base system does not (yet) contain a daemon for automatically establishing a UDP
     tunnel between a host behind a NAT router and a host on the Internet.

BSD					 January 4, 2009				      BSD


All times are GMT -4. The time now is 08:25 PM.

Unix & Linux Forums Content Copyrightę1993-2018. All Rights Reserved.
×
UNIX.COM Login
Username:
Password:  
Show Password