HOSTNAME(1) Linux Programmer's Manual HOSTNAME(1)
hostname - show or set the system's host name
domainname - show or set the system's NIS/YP domain name
ypdomainname - show or set the system's NIS/YP domain name
nisdomainname - show or set the system's NIS/YP domain name
dnsdomainname - show the system's DNS domain name
hostname [-a|--alias] [-d|--domain] [-f|--fqdn|--long] [-A|--all-fqdns] [-i|--ip-address]
[-I|--all-ip-addresses] [-s|--short] [-y|--yp|--nis]
hostname [-b|--boot] [-F|--file filename] [hostname]
hostname [-h|--help] [-V|--version]
domainname [nisdomain] [-F file]
ypdomainname [nisdomain] [-F file]
nisdomainname [nisdomain] [-F file]
Hostname is used to display the system's DNS name, and to display or set its hostname or
NIS domain name.
When called without any arguments, the program displays the current names:
hostname will print the name of the system as returned by the gethostname(2) function.
domainname will print the NIS domainname of the system. domainname uses the gethost-
name(2) function, while ypdomainname and nisdomainname use the yp_get_default_domain(3).
dnsdomainname will print the domain part of the FQDN (Fully Qualified Domain Name). The
complete FQDN of the system is returned with hostname --fqdn (but see the warnings in sec-
tion THE FQDN below).
The function gethostname(2) is used to get the hostname. When the hostname -a, -d, -f or
-i is called will gethostbyname(3) be called. The difference in gethostname(2) and geth-
ostbyname(3) is that gethostbyname(3) is network aware, so it consults /etc/nsswitch.conf
and /etc/host.conf to decide whether to read information in /etc/hostname or /etc/hosts
When called with one argument or with the --file option, the commands set the host name or
the NIS/YP domain name. hostname uses the sethostname(2) function, while all of the three
domainname, ypdomainname and nisdomainname use setdomainname(2). Note, that this is
effective only until the next reboot. Edit /etc/hostname for permanent change.
Note, that only the super-user can change the names.
It is not possible to set the FQDN or the DNS domain name with the dnsdomainname command
(see THE FQDN below).
The host name is usually set once at system startup (normally by reading the contents of a
file which contains the host name, e.g. /etc/hostname).
The FQDN (Fully Qualified Domain Name) of the system is the name that the resolver(3)
returns for the host name, such as, ursula.example.com. It is usually the hostname fol-
lowed by the DNS domain name (the part after the first dot). You can check the FQDN using
hostname --fqdn or the domain name using dnsdomainname.
You cannot change the FQDN with hostname or dnsdomainname.
The recommended method of setting the FQDN is to make the hostname be an alias for the
fully qualified name using /etc/hosts, DNS, or NIS. For example, if the hostname was
"ursula", one might have a line in /etc/hosts which reads
127.0.1.1 ursula.example.com ursula
Technically: The FQDN is the name getaddrinfo(3) returns for the host name returned by
gethostname(2). The DNS domain name is the part after the first dot.
Therefore it depends on the configuration of the resolver (usually in /etc/host.conf) how
you can change it. Usually the hosts file is parsed before DNS or NIS, so it is most com-
mon to change the FQDN in /etc/hosts.
If a machine has multiple network interfaces/addresses or is used in a mobile environment,
then it may either have multiple FQDNs/domain names or none at all. Therefore avoid using
hostname --fqdn, hostname --domain and dnsdomainname. hostname --ip-address is subject to
the same limitations so it should be avoided as well.
Display the alias name of the host (if used). This option is deprecated and should
not be used anymore.
Displays all FQDNs of the machine. This option enumerates all configured network
addresses on all configured network interfaces, and translates them to DNS domain
names. Addresses that cannot be translated (i.e. because they do not have an appro-
priate reverse DNS entry) are skipped. Note that different addresses may resolve to
the same name, therefore the output may contain duplicate entries. Do not make any
assumptions about the order of the output.
Always set a hostname; this allows the file specified by -F to be non-existant or
empty, in which case the default hostname localhost will be used if none is yet
Display the name of the DNS domain. Don't use the command domainname to get the
DNS domain name because it will show the NIS domain name and not the DNS domain
name. Use dnsdomainname instead. See the warnings in section THE FQDN above, and
avoid using this option.
-f, --fqdn, --long
Display the FQDN (Fully Qualified Domain Name). A FQDN consists of a short host
name and the DNS domain name. Unless you are using bind or NIS for host lookups you
can change the FQDN and the DNS domain name (which is part of the FQDN) in the
/etc/hosts file. See the warnings in section THE FQDN above, and avoid using this
option; use hostname --all-fqdns instead.
-F, --file filename
Read the host name from the specified file. Comments (lines starting with a `#')
Display the network address(es) of the host name. Note that this works only if the
host name can be resolved. Avoid using this option; use hostname --all-ip-addresses
Display all network addresses of the host. This option enumerates all configured
addresses on all network interfaces. The loopback interface and IPv6 link-local
addresses are omitted. Contrary to option -i, this option does not depend on name
resolution. Do not make any assumptions about the order of the output.
Display the short host name. This is the host name cut at the first dot.
Print version information on standard output and exit successfully.
-y, --yp, --nis
Display the NIS domain name. If a parameter is given (or --file name ) then root
can also set a new NIS domain.
Print a usage message and exit.
The address families hostname tries when looking up the FQDN, aliases and network
addresses of the host are determined by the configuration of your resolver. For instance,
on GNU Libc systems, the resolver can be instructed to try IPv6 lookups first by using the
inet6 option in /etc/resolv.conf.
/etc/hostname Historically this file was supposed to only contain the hostname and not the
full canonical FQDN. Nowadays most software is able to cope with a full FQDN here. This
file is read at boot time by the system initialization scripts to set the hostname.
/etc/hosts Usually, this is where one sets the domain name by aliasing the host name to
Peter Tobias, <firstname.lastname@example.org>
Bernd Eckenfels, <email@example.com> (NIS and manpage).
Michael Meskes, <firstname.lastname@example.org>
net-tools 2009-09-16 HOSTNAME(1)