10 More Discussions You Might Find Interesting
1. Ubuntu
I suddenly don't see my folders into /mnt/md0.
What can be reason?
mdadm --detail /dev/md*
/dev/md0:
Version : 1.2
Creation Time : Fri Jan 18 09:54:27 2019
Raid Level : raid1
Array Size : 1953383488 (1862.89 GiB 2000.26 GB)
Used Dev Size : 1953383488 (1862.89 GiB... (8 Replies)
Discussion started by: tomislav91
8 Replies
2. UNIX for Advanced & Expert Users
Currently I am using this laborious command
lvdisplay | awk '/LV Path/ {p=$3} /LV Name/ {n=$3} /VG Name/ {v=$3} /Block device/ {d=$3; sub(".*:", "/dev/dm-", d); printf "%s\t%s\t%s\n", p, "/dev/mapper/"v"-"n, d}'
Would like to know if there is any shorter method to get this mapping of... (2 Replies)
Discussion started by: royalibrahim
2 Replies
3. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
4. Red Hat
Good morning
Recently we needed to change the password from a redhat 6.5 system that no one knew the root password.
Starting the system with the init=/bin/bash method took us to the following scenario:
system_vg active with only root_lv and tmpfs mounted.
our entries at fstab are like... (1 Reply)
Discussion started by: Ikaro0
1 Replies
5. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
6. Solaris
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies
7. Red Hat
Hi,
I had a doubt regarding device mapper notations and their corresponding LVM volumes.
I have configured a volume group with two logical volumes in it as root and swap.
The entries in the /etc/fstab file show the dm notations namely,
/dev/mapper/VolGroup00-LogVol01... (2 Replies)
Discussion started by: kanna_geekworkz
2 Replies
8. Red Hat
I have an HP blade with Qlogic HBA's connected to an EVA8000. I have downloaded the latest multipath.conf from HP's website. The drive presented to the server appears to be configured and working except the output of "multipath -l" shows for all paths. What is causing this output?
mpath0... (2 Replies)
Discussion started by: manzier
2 Replies
9. Solaris
Hi.
I need to move a 5 disk RAID5 array from a SE3310 box to a different SE3310 array. After installing the disks in the "new" StorEdge device, I "would like" ;) to be able have access to the data which is on the RAID.
Essentially, the quesion is, how can this be done? :confused:
I checked... (5 Replies)
Discussion started by: alexs77
5 Replies
10. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
raidstart(8) System Manager's Manual raidstart(8)
NAME
raidstart, raidstop, - command set to manage md devices.
SYNOPSIS
raidstart [options] <raiddevice>*
raidstop [options] <raiddevice>*
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple disks to be combined into a single
filesystem, possibly with automated backup and recovery. Linux RAID devices are implemented through the md device driver.
If you're using the /proc filesystem, /proc/mdstat gives you informations about md devices status.
Currently, Linux supports linear md devices, RAID0 (striping), RAID1 (mirrroring), and RAID4 and RAID5. For information on the various lev-
els of RAID, check out:
http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/
for new releases of the RAID driver check out:
ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha
Avaible commands are :
mkraid : configures (creates) md (RAID) devices in the kernel, banding multiple devices into one.
raidstart : activates (starts) an existing 'persistent' md device
raid0run : activates old nonpersistent RAID0/LINEAR md devices
raidstop : turns off an md device, and unconfigures (stops) it
By default, a systems RAID configuration is kept in /etc/raidtab, which can configure multiple RAID devices.
All of these tools work similiarly. If -a (or --all) is specified, the specified operation is performed on all of the RAID devices men-
tioned in the configuration file. Otherwise, one or more RAID devices must be specified on the command line. For example:
raid0run -a
Starts all of the 'old' RAID0 RAID devices specified in /etc/raidtab. If only /dev/md1 should be started, the following command should be
used instead:
raidstart /dev/md1
OPTIONS
-a, --all
Apply the command to all of the configurations specified in the config file.
-c, --configfile filename
Use filename as the configuration file (/etc/raidtab is used by default).
-h, --help
Displays a short usage message, then exits.
-V, --version
Displays a short version message, then exits.
NOTES
The raidtools are derived from the md-tools and raidtools packages, which were originally written by Marc Zyngier, Miguel de Icaza, Gadi
Oxman, Bradley Ward Allen, and Ingo Molnar.
BUGS
no known bugs.
SEE ALSO
raidtab(5), raid0run(8), raidstop(8), mkraid(8)
raidstart(8)