Visit Our UNIX and Linux User Community


Connecting SGI to Linksys router


 
Thread Tools Search this Thread
Special Forums IP Networking Connecting SGI to Linksys router
# 1  
Old 02-16-2002
Question Connecting SGI to Linksys router

I have an SGI running Irix 6.5 and I am trying to connect it to my home network that consists of two Windows PC's (Win 98SE and Win 2000) plus the SGI all connected to a Linksys router which is connected to my DSL modem. My ISP is Verizon DSL (Dynamic IP addressing.)

All network lights are working.

I tried configuring my network setting on Irix using the IP address of the router since it handles the connection to the WAN.

I tried setting it up using DHCP as well as manually setting it up using the ISP my router gives it, but I just can't seen to get it to work.

If I type in /usr/etc/proclaim, I get the error message "failed to
configure ec0 as banas3. Cannot access primary interface, ec0. Using standalone network mode."

I have the following info for my SGI:
HostIPaddress: 192.168.1.101
DHCPservername:
MessageType: 5
NetworkMask: 0xffffff00
Routers: 192.168.1.1
DNSservers: 151.198.0.39 151.198.0.38
LeaseTimeInSecs: 86400
ServerIPAddress: 192.168.1.1

The Linksys router's IP address is 192.168.1.1

I am not sure why the DNS servers are listed as above (I don't know how to remove them.)

The two Windows PC's work just fine on my network.

Any ideas as to what I should do?
# 2  
Old 02-18-2002
I am new at Unix stuff... so I am not really sure what you are not able to do, but I am guessing that you cannot see the network.

Can you ping the gateway (router) IP? If not you may not have a default route pointing to the gateway.

Steve
# 3  
Old 02-25-2002
I got it to work. Thanks for the help.
# 4  
Old 04-26-2008
My exact problem. I'm running IRIX 6.5 on an SGI O2.

it was working on a network where it came from.

How about a step by step "I got it to work for dummies". Smilie

Linksys told me I had to configure my machine to

IP:192.168.1.20
SubNet Mask:255.255.255.0
Default Gateway:192.168.1.1
DNS:68.87.69.146 and DNS2: 68.87.85.98

I need to use this workstation at home and am completely new to UNIX.

I know about the etc/ in the root directory and that's about it...

Previous Thread | Next Thread
Test Your Knowledge in Computers #65
Difficulty: Easy
In the TCP/IP model, end-to-end connectivity is provided from host-to-host in the transport layer.
True or False?

10 More Discussions You Might Find Interesting

1. Hardware

SUN V245 Connecting To router Through Alom

Hello. I have a sun v245 and I have no hard drive for it yet but i would like to connect it to my home router by ethernet cable so I can use Alom remotely. Could someone please tell me how to set it up. Thank You (1 Reply)
Discussion started by: SunV245
1 Replies

2. UNIX for Dummies Questions & Answers

[Solved] Can't get on internet with Linux Static IP address and Linksys Router.

I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet. When I switch back to "Automatically obtain IP address" ..then I can get on the internet. Can comeone help with this. (2 Replies)
Discussion started by: FrankOscar
2 Replies

3. Cybersecurity

Linksys router question

Hi I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop. Yes. I did enable encryption to connect. Also my wireless printer is connected to that. For some reason, last night around 12:30 AM, the... (4 Replies)
Discussion started by: samnyc
4 Replies

4. IP Networking

Linksys RV802 VPN Router

Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more. ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100 (1 Reply)
Discussion started by: jgt
1 Replies

5. Shell Programming and Scripting

using wget to submit a form on linksys router

I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below). http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127 Here is my wget command: wget --http-user=xyz --http-password=xyz... (1 Reply)
Discussion started by: mike909
1 Replies

6. IP Networking

linksys router and solaris 8

I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I... (10 Replies)
Discussion started by: nicomen
10 Replies

7. IP Networking

router Linksys

I have a linksys router BEFSR41. I am trying to connect two network.. one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95. In the configuration LAN ip address by default it 192.168.1.1 If I define LAN IP to... (0 Replies)
Discussion started by: ajnabi
0 Replies

8. Solaris

I can't ping my linksys router from Ultra 10

To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still... (3 Replies)
Discussion started by: cstovall
3 Replies

9. IP Networking

cannot ping router from sgi irix

anyone available to help me config sgi octane to netscape and networking mac os X? i have three macs and one sgi. setup on a dsl netopia router. all 4 computers can ping each other by addresses and by names. all the macs can ping the router, but the sgi cannot ping the router, "network is... (0 Replies)
Discussion started by: eidde
0 Replies

10. IP Networking

Connecting SGI to Windows PC

I am trying to network an SGI running Irix 6.5 through an ethernet line to a PC running Windows 2000 (I have connected other PC's to this PC without any problems.) The PC has a DSL connection from Verizon that does not support Unix. I tried using DHCP on the SGI, but when I open a web browser on... (2 Replies)
Discussion started by: mdbanas
2 Replies

Featured Tech Videos