|
|
Sponsored Content
Special Forums
IP Networking
Connecting SGI to Linksys router
Post 15603 by mdbanas on Saturday 16th of February 2002 09:41:12 PM
02-16-2002
Connecting SGI to Linksys router
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I am trying to network an SGI running Irix 6.5 through an ethernet line to a PC running Windows 2000 (I have connected other PC's to this PC without any problems.) The PC has a DSL connection from Verizon that does not support Unix. I tried using DHCP on the SGI, but when I open a web browser on... (2 Replies)
Discussion started by: mdbanas
2 Replies
2. IP Networking
anyone available to help me config sgi octane to netscape and networking mac os X?
i have three macs and one sgi. setup on a dsl netopia router.
all 4 computers can ping each other by addresses and by names.
all the macs can ping the router, but the sgi cannot ping the router, "network is... (0 Replies)
Discussion started by: eidde
0 Replies
3. Solaris
To begin with, I am a Solaris newbie; however, I am very familiar with Linux. Until I began working with Solaris, I didn't realize how much more difficult networking Solaris is than Linux. Before submitting this question, I have tried to fix this problem myself. After days of research, I still... (3 Replies)
Discussion started by: cstovall
3 Replies
4. IP Networking
I have a linksys router BEFSR41. I am trying to connect two network..
one device has to route from one network of IP address 192.168.10.12 to go to a device on separate network with IP address 192.168.25.95.
In the configuration LAN ip address by default it 192.168.1.1
If I define LAN IP to... (0 Replies)
Discussion started by: ajnabi
0 Replies
5. IP Networking
I just sys-unconfigged my ultra sparc which is on my home network where I have 2 PCs attached. When I go to install Solaris 8, it asks various things re: networking. Specifically, when it asks for the IP addy for the DNS server, I input the info, but it barfs back "IP addy info not found". I... (10 Replies)
Discussion started by: nicomen
10 Replies
6. Shell Programming and Scripting
I'm trying to use wget to submit a form. I have tried to dig out what is actually being "posted" and where, using tamperdata (see below).
http://ubuntuforums.org/attachment.php?attachmentid=109123&d=1239224127
Here is my wget command:
wget --http-user=xyz --http-password=xyz... (1 Reply)
Discussion started by: mike909
1 Replies
7. IP Networking
Does anyone know if this router can restrict incoming traffic to specific IP addresses. There does not seem to be any information on Cisco's web site any more.
ie Only 209.123.123.123 is allowed access to port 9100, which is redirected to 192.168.1.100 (1 Reply)
Discussion started by: jgt
1 Replies
8. Cybersecurity
Hi
I have very basic network settings in my home. Cable connected to my Linksys Wireless G router. My wife and I connect to that using our laptop.
Yes. I did enable encryption to connect. Also my wireless printer is connected to that.
For some reason, last night around 12:30 AM, the... (4 Replies)
Discussion started by: samnyc
4 Replies
9. UNIX for Dummies Questions & Answers
I configured my linux server with Static IP address out of the range of the DHCP linksys router, but cannot get on the internet.
When I switch back to "Automatically obtain IP address" ..then I can get on the internet.
Can comeone help with this. (2 Replies)
Discussion started by: FrankOscar
2 Replies
10. Hardware
Hello.
I have a sun v245 and I have no hard drive for it yet but i would like to connect it to my home router by ethernet cable so I can use Alom remotely. Could someone please tell me how to set it up.
Thank You (1 Reply)
Discussion started by: SunV245
1 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5) NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage describes the vlan extensions to the standard interfaces(5) file format. Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener- ally needed when using (a lot of) vlans. VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to 4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names. iface eth0.1 inet static address 192.168.1.1 netmask 255.255.255.0 iface vlan1 inet static vlan-raw-device eth0 address 192.168.1.1 netmask 255.255.255.0 iface eth0.0001 inet static address 192.168.1.1 netmask 255.255.255.0 iface vlan0001 inet static vlan-raw-device eth0 address 192.168.1.1 netmask 255.255.255.0 # We don't have br support out of the box iface br0.2 inet static vlan-raw-device br0 address 192.168.1.1 netmask 255.255.255.0 # Aliases are ignored iface br0.2:1 inet static address 192.168.1.1 netmask 255.255.255.255 EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface. vlan-raw-device devicename Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name. ip-proxy-arp 0|1 Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices. ip-rp-filter 0|1|2 Set the return path filter for this specific interface. This also works on plain ethernet like devices. hw-mac-address mac-address This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address with the ip command. AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net> SEE ALSO
vconfig(8) interfaces(5) vlan September 30 2007 VLAN-INTERFACES(5)