configuring nic card

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Configuring NIC device in Solaris 9 SPARC OS [QEMU]

I have Xubuntu 18.04 installed on my PC. I have created a 10G .img image file created by QEMU-IMG. I have installed inside of it Solaris 9 SPARC edition . If I try and mount the image file as a loop device (using sudo losetup /dev/loop0 /path-to-img-file) I can only mount it as read only. ...

2. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

3. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

4. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

5. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

6. IP Networking

Problem configuring NIC in DGUX

Old DG box Aviion PentiumPro running R4.20Mu06 being used to try to recreate Ingres db from backup tapes so machine has not been operational before and some of original files in /etc may have ben overwritten Unable to get NIC working Any pointers on how to go about configuring NIC :rolleyes:

7. Solaris

Configuring 1 Nic card with 2 IP addresses and 2 seperate default Gateways in Solaris

Hi ...... I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways. ( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip) Thanks, Remi

8. HP-UX

Configuring NIC

Hi. I have HP-9000 Server running HP-UX 10.20. rECENTLY OUR network upgraded to 100mb/sec and I want to do same on the server. So, I add the second Network card (100MB). But the problem is, I can't find a way of configuring this card. How am i going to tell the server to use this 100mb card...

9. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

LEARN ABOUT REDHAT

dummy_cs

DUMMY_CS(4)						     Kernel Interfaces Manual						       DUMMY_CS(4)

NAME

       dummy_cs - PCMCIA dummy device driver

SYNOPSIS

       insmod dummy_cs.o [pc_debug=n] [free_ports=n] [irq_list=i,j,...]

DESCRIPTION

       The dummy_cs module has two purposes.  It is intended as a demonstration of how to write the PCMCIA interface code for a client driver, and
       the source code is heavily commented.  It is also written to function as a sort of generic ``point enabler'': when bound to any	PCMCIA	IO
       card,  it  will read the card's Configuration Information Structure, and configure the card appropriately.  The configuration includes set-
       ting up IO and memory windows, configuring the card for interrupts, and initializing the card's PCMCIA configuration registers.

       It turns out that many cards report incomplete or inaccurate configuration information, due to vendor carelessness and  the  complexity	of
       the  data format.  A vendor driver can generally take for granted many configuration details, so there is not much incentive for vendors to
       ensure that the on-card information is complete.  Thus, the dummy_cs module is limited by its generality: since	it  makes  no  assumptions
       about card types, it is forced to rely on the card information, for better or worse.

PARAMETERS

       pc_debug=n
	      Selects  the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.	A non-zero
	      value enables debugging.

       free_ports=n
	      A flag indicating if the IO ports allocated for the card should be freed from the kernel resource maps.  This is useful if the dummy
	      driver is being used to configure a card in preparation for loading a specific PCMCIA-unaware driver.  The default is 0 (false).

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2000/06/12 21:24:47						       DUMMY_CS(4)

HP-UX