8 More Discussions You Might Find Interesting
1. Solaris
I have installed Solaris 11 Express on my machine. On my GA-X58A-UD5 motherboard there are two 6 Gb/s SATA ports (Marvell 9128 chip), but when I connect a hard drive to one of them, the system does not recognize it.
However, when I boot from a USB install image (downloaded from here Oracle... (1 Reply)
Discussion started by: RychnD
1 Replies
2. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
6. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
7. UNIX for Advanced & Expert Users
i have a system which has two hard disks..one is sata and the other one is normal ata hard disk.
i wish to install red hat enterprise linux WS(desktop edition) on my sata hard disk..but the installer shows me only my ata hard disk..
i searched the net..it says that a library-- libata will let it... (2 Replies)
Discussion started by: ankit.jss
2 Replies
8. Solaris
can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it.
thanks and regards
msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies
LEARN ABOUT NETBSD
viaide
VIAIDE(4) BSD Kernel Interfaces Manual VIAIDE(4)
NAME
viaide -- AMD, NVIDIA and VIA IDE disk controllers driver
SYNOPSIS
viaide* at pci? dev ? function ? flags 0x0000
options PCIIDE_AMD756_ENABLEDMA
DESCRIPTION
The viaide driver supports the following IDE controllers and provides the interface with the hardware for the ata driver:
- Advanced Micro Devices AMD-756, 766, 768 and CS5536 IDE Controllers
- NVIDIA nForce, nForce2, nForce2 400, nForce3, nForce3 250, nForce4, MCP04, MCP55, MCP61, MCP65, MCP67 IDE and SATA Controllers.
- VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, VT8235, VT8237/VT8237R IDE Controllers, VT6421 Serial RAID
Controller and CX700 IDE Controller.
The 0x0002 flag forces the viaide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
NOTES
Drives on the VT6421 Serial RAID Controller can only be accessed after they have been configured into RAID or JBOD sets via its BIOS. It is
also inaptly named as it has both SATA and PATA interfaces.
BUGS
The AMD756 chip revision D2 has a bug affecting DMA (but not Ultra-DMA) modes. The workaround documented by AMD is to not use DMA on any
drive which does not support Ultra-DMA modes. This does not appear to be necessary on all drives, the PCIIDE_AMD756_ENABLEDMA option can be
used to force multiword DMA on the buggy revisions. Multiword DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4). The bug, if triggered, will cause a total system hang.
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
August 31, 2007 BSD