8 More Discussions You Might Find Interesting
1. Solaris
I have installed Solaris 11 Express on my machine. On my GA-X58A-UD5 motherboard there are two 6 Gb/s SATA ports (Marvell 9128 chip), but when I connect a hard drive to one of them, the system does not recognize it.
However, when I boot from a USB install image (downloaded from here Oracle... (1 Reply)
Discussion started by: RychnD
1 Replies
2. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
6. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
7. UNIX for Advanced & Expert Users
i have a system which has two hard disks..one is sata and the other one is normal ata hard disk.
i wish to install red hat enterprise linux WS(desktop edition) on my sata hard disk..but the installer shows me only my ata hard disk..
i searched the net..it says that a library-- libata will let it... (2 Replies)
Discussion started by: ankit.jss
2 Replies
8. Solaris
can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it.
thanks and regards
msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies
JMIDE(4) BSD Kernel Interfaces Manual JMIDE(4)
NAME
jmide -- JMicron Technology JMB36x PCIe to SATA II/PATA controller driver
SYNOPSIS
jmide* at pci? dev ? function ? flags 0x0000
ahcisata* at jmide?
DESCRIPTION
The jmide driver supports the JMicron Technology JMB36x IDE controllers.
These PCI-e controllers exist in different flavors (1 or 2 PATA Ultra/133 ports and/or 1 or 2 SATA-II ports), and are highly flexible. The
SATA ports can be attached to the integrated AHCI controller or attached to the PCI IDE channels in PATA emulation, in either single-drive
emulation on each PCI IDE channels, or in master/slave emulation on one of the PCI IDE channels.
When enabled, the AHCI controller can either be on the PCI function 0 or function 2. The PCI IDE controller can also be on either PCI func-
tion, and can share the PCI function with AHCI. The jmide driver supports both the AHCI controller and PCI IDE controller in various config-
urations.
SEE ALSO
ahcisata(4), ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
AUTHORS
The jmide driver was written by Manuel Bouyer.
BSD
July 2, 2007 BSD
