7 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I'm trying to develop an application to work with serial infra-red module, but I'm having difficulties to even get my module started. My HW is Beagleboard, which has 1 UART serial port, normally used for console, which I have disabled (I re-created the boot.scr, without the console... (0 Replies)
Discussion started by: julumme
0 Replies
2. UNIX for Advanced & Expert Users
Hi guys,
i'm running a program on samsumg 6410 arm cpu board. it caused an "free(): invalid next size (normal)" fail.
i try to use gdb for remote debugging:
1, start gdb server on board:
gdbserver 192.168.1.20:1234 ./HostAP
Process ./HostAP created; pid = 499
Listening on port... (8 Replies)
Discussion started by: ss1969
8 Replies
3. Programming
hi,
correct me if am wrong, as per gcc doc gcc is able to compile code for different target systems such as ARM, ARC etc. I tried for compiling ARM but failed to do so.
getting below error:
gcc -mcpu=arm920t -c avg.c -o agv_arm
`-mcpu=' is deprecated. Use `-mtune=' or '-march=' instead.... (6 Replies)
Discussion started by: zing_foru
6 Replies
4. Fedora
think only compile is required I wish to compile a sample code
int main()
{
int a=5,b=8,c;
c=a+b;
}
compile using gcc -Wall -g -march=arm922t main.c -o hello
I got an error
:bad value(arm922t) for -march=switch
instead of using march i used mcpu options ,the same... (1 Reply)
Discussion started by: sujith4u87
1 Replies
5. Programming
Running a multi-threaded program in my arm board one day or more ,The process down .
In order to get a coredump to analysis of the stack , . I use commands ulimited -c unlimited .
but when the process down . no coredump
But I write a test
#include <stdio.h>
int main(void){
... (14 Replies)
Discussion started by: aobai
14 Replies
6. UNIX for Advanced & Expert Users
Dear All,
I am having problem with read() system call in Blocking Mode.
In my driver interrupt intimation done through RT FIFO. so i have created the RT FIFO and open the FIFO using open() system call with O_RDONLY flag and i am waiting for interrupt using read() blocking call.initally... (1 Reply)
Discussion started by: rajamohan
1 Replies
7. Linux
Hi,
Does anybody have a good pointer on Linux kernel internals for ARM architecture? I can locate plenty for x86 but since ARM is RISC I think there would be subtle changes. So if somebody has a knowledge of good document on Linux Kernel internals for ARM or even a comparative study of kernel on... (0 Replies)
Discussion started by: Rakesh Ranjan
0 Replies
LEARN ABOUT DEBIAN
gnunet-arm
GNUNET-ARM(1) General Commands Manual GNUNET-ARM(1)
NAME
gnunet-arm - control GNUnet services
SYNOPSIS
gnunet-arm [options]
DESCRIPTION
gnunet-arm can be used to start or stop GNUnet services, including the ARM service itself. The ARM service is a supervisor for GNUnet's
service processes. ARM starts services on-demand or as configured and re-starts them if they crash.
OPTIONS
-c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
-e, --end
Shutdown all GNUnet services (including ARM itself). Running "gnunet-arm -e" is the usual way to shutdown a GNUnet peer.
-h, --help
Print short help on options.
-L LOGLEVEL, --loglevel=LOGLEVEL
Use LOGLEVEL for logging. Valid values are DEBUG, INFO, WARNING and ERROR.
-i SERVICE, --init=SERVICE
Starts the specified SERVICE if it is not already running. More specifically, this makes the service behave as if it were in the
default services list.
-k SERVICE, --kill=SERVICE
Stop the specified SERVICE if it is running. While this will kill the service right now, the service may be restarted immediately
if other services depend on it (service is then started 'on-demand'). If the service used to be a 'default' service, its default-
service status will be revoked. If the service was not a default service, it will just be (temporarily) stopped, but could be re-
started on-demand at any time.
-s, --start
Start all GNUnet default services on this system (and also ARM). Naturally, if a service is demanded by a default service, it will
then also be started. Running "gnunet-arm -s" is the usual way to start a GNUnet peer.
-I, --info
List all running services.
-v, --version
Print GNUnet version number.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO
gnunet-service-arm(1)
GNUnet Jan 4, 2012 GNUNET-ARM(1)