gnunet-arm(1) [debian man page]

GNUNET-ARM(1)						      General Commands Manual						     GNUNET-ARM(1)

NAME

       gnunet-arm - control GNUnet services

SYNOPSIS

       gnunet-arm [options]

DESCRIPTION

       gnunet-arm  can	be  used to start or stop GNUnet services, including the ARM service itself.  The ARM service is a supervisor for GNUnet's
       service processes.  ARM starts services on-demand or as configured and re-starts them if they crash.

OPTIONS

       -c FILENAME,  --config=FILENAME
	      Use the configuration file FILENAME.

       -e, --end
	      Shutdown all GNUnet services (including ARM itself).  Running "gnunet-arm -e" is the usual way to shutdown a GNUnet peer.

       -h, --help
	      Print short help on options.

       -L LOGLEVEL, --loglevel=LOGLEVEL
	      Use LOGLEVEL for logging.  Valid values are DEBUG, INFO, WARNING and ERROR.

       -i SERVICE,  --init=SERVICE
	      Starts the specified SERVICE if it is not already running.  More specifically, this makes the service behave as if it  were  in  the
	      default services list.

       -k SERVICE,  --kill=SERVICE
	      Stop  the  specified SERVICE if it is running.  While this will kill the service right now, the service may be restarted immediately
	      if other services depend on it (service is then started 'on-demand').  If the service used to be a 'default' service,  its  default-
	      service  status  will be revoked.  If the service was not a default service, it will just be (temporarily) stopped, but could be re-
	      started on-demand at any time.

       -s, --start
	      Start all GNUnet default services on this system (and also ARM).	Naturally, if a service is demanded by a default service, it  will
	      then also be started.  Running "gnunet-arm -s" is the usual way to start a GNUnet peer.

       -I, --info
	      List all running services.

       -v, --version
	      Print GNUnet version number.

BUGS

       Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>

SEE ALSO

       gnunet-service-arm(1)

GNUnet								    Jan 4, 2012 						     GNUNET-ARM(1)

GNUNET-VPN(1)						      General Commands Manual						     GNUNET-VPN(1)

NAME

       gnunet-vpn - manually setup a GNUnet VPN tunnel

SYNOPSIS

       gnunet-vpn [options]

DESCRIPTION

       gnunet-vpn  can	be  used  to manually setup a VPN tunnel via the GNUnet network.  There are two main types of tunnels.	Tunnels to an exit
       node which routes the traffic to the global Internet, and tunnels to a node that runs a service only within GNUnet.  Depending on the  type
       of  tunnel, gnunet-vpn takes different options.	The "-i" option is required for tunnels to an exit node, whereas the "-p" and "-s" options
       in conjunction with either "-u" or "-t" are required for tunnels to services.  For exit tunnels, both UDP and TCP  traffic  will  be  redi-
       rected.	For service tunnels, either UDP ("-u") or TCP ("-t") traffic will be redirected.

       The  tool  will	display the IP address for this end of the tunnel.  The address can be displayed as soon as it has been allocated, or only
       after ("-a") the tunnel has been created.

OPTIONS

       -4, --ipv4
	      Desired IP address on this end of the tunnel should be an IPv4 address.

       -6, --ipv6
	      Desired IP address on this end of the tunnel should be an IPv6 address.

       -a, --after-connect
	      Display IP address only after the tunnel is fully connected.

       -c FILENAME,  --config=FILENAME
	      Use the configuration file FILENAME.

       -d SEC, --duration SEC
	      The mapping should be established for SEC seconds.  Default is 5 minutes.

       -h, --help
	      Print short help on options.

       -i IP, --ip IP
	      Tunnel should be to an exit node and connect to the given IPv4 or IPv6 IP address.  Note that you can specify an IPv6 address as the
	      target here, even in combination with "-4" (4to6) and similarly you can specify an IPv4 address in combination with "-6" (6to4).

       -L LOGLEVEL, --loglevel=LOGLEVEL
	      Use LOGLEVEL for logging.  Valid values are DEBUG, INFO, WARNING and ERROR.

       -p PEERID,  --peer=PEERID
	      Name of the peer offering the service to connect to.  Cannot be used in conjunction with "-i", requires "-s".

       -s NAME,  --service=NAME
	      Name of the service running on the target peer.  Cannot be used in conjunction with "-i", requires "-p".

       -t, --tcp
	      Service runs TCP.  Either "-t" or "-u" must be specified when using "-s".

       -u, --udp
	      Service runs UDP.  Either "-t" or "-u" must be specified when using "-s".

       -V, --verbose
	      Be verbose.

       -v, --version
	      Print GNUnet version number.

BUGS

       Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>

SEE ALSO

       gnunet-setup(1)

GNUnet								    25 Feb 2012 						     GNUNET-VPN(1)