Tape drive ?? fast/wide scsi box + dds4??


 
Thread Tools Search this Thread
Special Forums Hardware Filesystems, Disks and Memory Tape drive ?? fast/wide scsi box + dds4??
# 1  
Old 10-08-2002
Tape drive ?? fast/wide scsi box + dds4??

I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use for software? I have to keep this under 1500 (boss gave me a budget). The dds4 tape drive i had in mind tho uses ultra scsi, i have 68 pin fast/wide scsi on my ultra2. Will ultra scsi work with the fast/wide scsi? What software would work to help automate the backups across different platforms? Trying to figure out what others use, our corporate uses a tape loader and does incremental backups every few minutes, but I'm not looking for that high end of backups. Just a daily where I could use one tape per system kind of thing.
# 2  
Old 10-08-2002
The DDS4 drive should work, but of course, it won't be as fast as it could be with the UltraWide controller. I believe that I have ran a similiar setup of an UltraWide device on old SCSI-II bus with a 50 to 68 pin adapter. I have also ran a Ultra160 10,000 RPM 18 gig SCSI drive on my 2940UW controller. It works, but I don't get all the Ultra160 bandwidth which really cripples the drives performance (Imagine my surprise when my ATA100 drives were outrunning my uberfast spinning drive. Sure, the head seek was heckuva lot faster than my IDEs, but the data throughput was really disapointing...)

As for software, I would take a look at Amanda. It is built for backing up over a network of several machines.
# 3  
Old 10-08-2002
amanda

I cannot figure out how to set up amanda, driving me nuts. Is there a good site that shows step by step. I have it on my linux box, configured, installed, etc, but can't figure out all the conf stuff, there's so much and its spread out all over the directories.
# 4  
Old 10-08-2002
Here is one website that I got from Google: http://www.frankenlinux.com/guides/amandaserver.html

I have also seen articles in SysAdmin magazine on setting up amanda (don't have 'em on me at the moment. Someplace back at the house, I reckon).
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Solaris

Sun E220R + HP (SCSI) LTO Ultrium Tape Drive

Hi all, this time I'd need a help from an advanced Solaris system admin :rolleyes: I attached a HP StorageWorks Ultrium 215 Tape Drives - Overview - c00059530 - HP Business Support Center to my Sun E220R and it got recognized immediately (probe-scsi-all). Now the operating system boot process... (8 Replies)
Discussion started by: pseudocoder
8 Replies

2. Hardware

Help with scsi tape drive problem

I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies

3. UNIX for Dummies Questions & Answers

Problems with SCSI card and tape drive

Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies

4. AIX

external DDS4 Tape Drive

Hi folks, I've got a little problem concerning my external dds4 tape drive. I've got 2 rs6000 systems, one has a external dds4 tape drive attached, I want to attach the tape drive to the other rs6000 system so that i can restore data from the 1st rs6000 on to the second. Does anybody has... (3 Replies)
Discussion started by: Erik Rooijmans
3 Replies

5. SCO

Installing SCSI Tape drive

Hello, I'm having some issues with installing SCSI tape drive on SCO 5.0.6 hardware config shows the following adapters %adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto %adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd %adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies

6. Filesystems, Disks and Memory

The best partitioning schem for a 250GB Sata hard drive & a 75GB SCSI hard drive

Hi I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies

7. Solaris

mounting an external scsi tape drive

hi- I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies

8. Filesystems, Disks and Memory

help installing Sun 8mm unipack scsi tape drive

Hi all, please help I am stuck. I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies

9. UNIX for Dummies Questions & Answers

Scsi tape drive.

I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies

10. UNIX for Dummies Questions & Answers

how to mount a hotswap scsi drive on a solaris 2.6 netra box using the mount command?

Hi... question is this: How do I mount an LVD hotswap scsi drive in bay #2 on a netra using the mount command? volmgt doesn't seem to mount it and/or I don't know how to view the drives data if it's formatted which it may not be. This drive is not new out of the box so I'm not sure. ... (4 Replies)
Discussion started by: soulshaker
4 Replies
Login or Register to Ask a Question