9 More Discussions You Might Find Interesting
1. AIX
I am new to the AIX operating system and am seeking out some advice. We recently have had a drive go bad on our AIX server that is in a RAID 10 array. We have a replacement on the way. I was wondering what the correct steps are to swap out this drive. Does the server need to be powered off? Or can... (5 Replies)
Discussion started by: mpeter05
5 Replies
2. SCO
Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin.
I get a Transition to ready failure on ha=0* message when the... (4 Replies)
Discussion started by: psytropic
4 Replies
3. Hardware
Hey All,
Im using Fedora 2.6 (which is cannot be changed for compatibility reasons).
I cloned a drive from a different server and when i added this drive to a new box, during startup it hangs on "Configuring Kernel Parameters:"
Is there any way to bypass this process and still boot... (0 Replies)
Discussion started by: robfwauk
0 Replies
4. AIX
I have 2 LPARs running AIX 5.3. Both are on the same VLAN. One LPAR, which I'll call LPAR2, has a 4mm SCSI tape drive connected to it, while LPAR1 does not have a tape drive connected. I am able to take mksysb backups of LPAR2 to the tape drive since it's directly connected. However, I need to... (2 Replies)
Discussion started by: need2bageek
2 Replies
5. SCO
Hello Unix World,
I've been having this issue for the longest time.
Here is my setup
OS: SCO OpenServer 6.0 with mp4, mp3
Server: Dell PowerEdge 840, 800, 2900
USB Stick: Patriot 16GB High Speed, and many other different brands.
Occasinaly while system is running and USB is pluged in the... (0 Replies)
Discussion started by: miles556
0 Replies
6. AIX
Every 3 months we have to do backups (smitth mksysb/lsmksysb + tar) on at least 30 workstations. We have to carry around 2 external tape drives to connect to them. It is a pain to do because it takes at least 3 days to do (evening/night shift) and users sometimes complain that there desk is not put... (1 Reply)
Discussion started by: Browser_ice
1 Replies
7. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
8. UNIX for Dummies Questions & Answers
:confused: ........I have a new hard drive and I need to copy ALL info from the old to the new. I would like to use the dd command. I know the command is as follows......
dd if=/dev/rdsk/c1t1d0s0 of=/dev/rdsk/????????
Where I have the question marks is the problem.
How do I find out what the... (4 Replies)
Discussion started by: shorty
4 Replies
9. UNIX for Advanced & Expert Users
I have suns machine that holds two hard drives. I only used one. I tryed to make a lan network with my windows xp. When I tryed to restart the machine it wanted to a password. when before I just typed root to log in. So i edited the etc dir. big mistake. So now the machine will not read the hard... (2 Replies)
Discussion started by: victbla
2 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)