9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I'm writing a simple USB driver to drive a stepper motor based on USB Skeleton 2.2 Driver, kernel 3.8. The basic version is running properly. As a advancement, I introduced KTHREAD to call the DEVICE_WRITE (skel_write) (), so that the driver will be available for other tasks & requests.
Calling... (0 Replies)
Discussion started by: miteshgaware
0 Replies
2. Linux
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Discussion started by: gacanepa
0 Replies
3. Solaris
Hello all;
We have a SunFire V240 with three disks that were part of a metadb. One of those disks, the boot disk, experienced a horrible death Monday night and we're now trying to recover from that.
I know very little about metadb stuff, so please be gentle with me...
I'm assuming... (3 Replies)
Discussion started by: Handon
3 Replies
4. Red Hat
Hello, everyone.
I am using Fedora 15, and want to upgrade to version 16. I follow the official link Upgrading Fedora using yum - FedoraProject to upgrade my OS by the following command:
yum update kernel* --releasever=16
yum groupupdate Base --releasever=16
reboot
After reboot, OS... (2 Replies)
Discussion started by: 915086731
2 Replies
5. Ubuntu
Hello Everyone,
First of all, I highly appreciate all Linux forum members and whole Linux community. http://forums.linuxmint.com/images/smilies/icon_wink.gif. I wish you the best for all of you !
I will try to be short and concise: I am using Linux Mint 10 for 2 months on 2 ws, and all went... (3 Replies)
Discussion started by: cdt
3 Replies
6. UNIX for Dummies Questions & Answers
I compiled new kernel in linux 10.04 called linux-2.6.26.8-xenomai, it runs alongside the other kernel, but when I want to boot it I get an error message saying:
Missing modules (cat /proc/modules; ls /dev)
ALERT! /dev/sda5 does not exist.
After making the modules and headers
I made the... (4 Replies)
Discussion started by: mdop
4 Replies
7. HP-UX
Hi gurus,
I was more on the Sun side and now am getting exposure to the HP-UX side of the world. I have to upgrade firmware on BL870c blade.
Can some one point to a url or give procedure to follow as I couldn't find much on the web.
Thanks
Momin (1 Reply)
Discussion started by: momin
1 Replies
8. BSD
Salamo Alikom after recompilation my kernel does not boot and display msg said : enter full path to bash : /bin/sh i try fsck -r ,fsck -y but the problem is steel . my make.conf : PERL_VER=5.8.8 OVERRIDE_LINUX_BASE_PORT=f8 PERL_VERSION=5.8.8 MODULES_OVERRIDE = linux acpi accf_http pccard msdosfs... (1 Reply)
Discussion started by: SIFE
1 Replies
9. SCO
I tried to add ppp on a serial line tty1b and I relink the kernel. Now, I would like to boot from the previous kernel because I lost the connexion for the others terminal (serial lines) too.
I would appreciate any help. (3 Replies)
Discussion started by: pacctono
3 Replies
INTRO(8) BSD System Manager's Manual INTRO(8)
NAME
intro -- introduction to system maintenance procedures and commands
DESCRIPTION
This section contains information related to system operation and maintenance.
It describes commands used to create new file systems (newfs(8)), verify the integrity of the file systems (fsck(8)), control disk usage
(edquota(8)), maintain system backups (dump(8)), and recover files when disks die an untimely death (restore(8)). Network related services
like inetd(8) and ftpd(8) are also described.
All commands set an exit status. Its value may be tested to see if the command completed normally. Unless otherwise noted (rare), the value
0 signifies successful completion of the command, while a value >0 indicates an error. Some commands attempt to describe the nature of the
failure by using error codes defined in sysexits(3), or set the status to arbitrary values >0 (typically 1), but many such values are not
described in the manual.
A number of pages in this section describe general system management topics.
For example, the boot(8) manual page describes the system bootstrapping procedures, and the diskless(8) manual page describes how to boot a
system over a network. The crash(8) manual page should be consulted to understand how to interpret system crash dumps.
HISTORY
The intro section manual page appeared in 4.2BSD.
BSD
October 22, 2006 BSD
