H50 power issue

Thread Tools Search this Thread
Operating Systems AIX H50 power issue
# 1  
Old 02-26-2008
H50 power issue

Hi all,

I have a H50 server in a remote location and the cron has the power failure line entered. There is nothing in errpt so I suspect this may have been added some time ago.

How can I determine the status of the power supplies remotely?

# 2  
Old 02-26-2008
As errpt is OK you are probably right and they are old messages.

Run advanced diags in system verification to sysplanar0, if they pass then remove the rc.powerfail from cron, all should be OK.

If you want to make double sure al is OK you'll need to power down and then cold boot for the full post / bist tests to run, or if you cannot do this remotely then you'll need to get to site to do it and while there check the power status lights on the power supplies.
Login or Register to Ask a Question

Previous Thread | Next Thread

7 More Discussions You Might Find Interesting

1. AIX

Power HA 6.1 Bring Resource group online issue

Hi all, I have the following in hacmp.out for bringing Resource group online. Volume groups themselves are Enhanced-Capable and on each node I can varyon and mount filesystems. +main1_rg_01:cl_activate_vgs STATUS=0 +main1_rg_01:cl_activate_vgs typeset -li STATUS +main1_rg_01:cl_activate_vgs... (2 Replies)
Discussion started by: OdilPVC
2 Replies

2. AIX

Issue with RS/6000 H50 from IBM

G'day all I have purchased 2 big IBM H50 RS/6000 enterprise servers. I am led to believe they are running AIX 4.3.3. Now problem is getting into remote console and turning off remote console and enabling my graphics card which i have installed. Now i was told to remove it, and try again. But i... (17 Replies)
Discussion started by: ADS2459
17 Replies

3. AIX

How to tell Power 4/5/6

I'm looking for a way - from the command line - to tell whether a given AIX system I have is a Power5, Power4 or Power6 machine - it seems like there would be an option to 'uname' but I couldn't find one. Thanks! (3 Replies)
Discussion started by: thomn8r
3 Replies

4. UNIX for Dummies Questions & Answers

Sun ultra enterprise 450 power issue

I've search the forum and came up with someone having the same issue where the power does not going to the main board. I turn the key and nothing, no lights or anything moving. I have another board put it in the same system and it works just fine. Please help, thank you in advance. (2 Replies)
Discussion started by: vhtran
2 Replies

5. Solaris

Failed to power up

Dear expert, I have one server,in /var/adm/messages everyday present these messages: Jan 3 06:01:30 SERVERGINTING genunix: WARNING: Device /pci@1d,700000/pci@1/scsi@2,1/sd@5,0 failed to power up. Jan 3 06:01:31 SERVERGINTING scsi: WARNING: /pci@1d,700000/pci@1/scsi@2,1/sd@5,0 (sd45):... (2 Replies)
Discussion started by: fredginting
2 Replies

6. Solaris

Power management issue with Ultra45

Hi Frnds, Need a help. My solaris box ultra 45 is loaded with solaris 10. After idle for 10 minutes its going for power save mode,but when i hit enter key or make a movement in mouse the screen is not resuming. Sometimes it comes back after 10 mins and sometimes it doesnt .i am rebooting the... (0 Replies)
Discussion started by: sriram.s
0 Replies

7. UNIX for Dummies Questions & Answers

Power Cycling

Hello Friends , I have been reading some of the Sys Admin notes when i came across a term "Power Cycling" Can anybody please explain what this means Thank You (1 Reply)
Discussion started by: DPAI
1 Replies
Login or Register to Ask a Question