10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
2. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
3. Solaris
My Customer has the requirement to use IPMP instead of LACP cause of giving Switch-Management to others (Outsourcing).
I deleted the aggregation with
And created an IPMP-Configuration:
with all Entries under /etc/hosts /etc/netmasks and /etc/defaultrouter
But i end up with one interface... (3 Replies)
Discussion started by: etomer_sk
3 Replies
4. Solaris
Hello,
I have these S10 boxes with LACP using the L4 policy. Does the L4 policy create a lot more overhead as opposed to using the L2?
I'm noticing that my traffic does not seem to be very well load balanced accross the NIC's, and I am wondering if the policy I'm using has anything else to do... (1 Reply)
Discussion started by: BG_JrAdmin
1 Replies
5. Shell Programming and Scripting
Hello All,
I am writing an shell script but abruptly its not able to recognize switches in echo statement.
#!/bin/bash
top -n 1 -b>ankit
host=`hostname`
time=`cat ankit|grep load|tr -s " "|cut -d " " -f3`
load=`cat ankit|grep load|tr -s " "|cut -d "," -f4|cut -d ":" -f2`
... (3 Replies)
Discussion started by: ajaincv
3 Replies
6. Infrastructure Monitoring
Hi, I have configured check_snmp plugin and using the plugin i am able to monitor the uptime of the switch.
But the following fails
# /usr/local/nagios/libexec/check_snmp -H 10.10.10.1 -C ready -o ifOperStatus.1 -r 1 -m RFC1213-MIB
SNMP CRITICAL - *down(2)* |
#
Any suggestions ? (1 Reply)
Discussion started by: uxadmin007
1 Replies
7. IP Networking
Hello,
I'm working on LACP architecture. I would like to know if it's possible to aggregate two links on two separate switches.
Here an example I want : Aggregation of link1 and link2 to obtain a logical 2 gbit/s link. Also have redundancy, if one of them is down, the traffic goes through the... (1 Reply)
Discussion started by: jbemonet
1 Replies
8. IP Networking
Hello, I am trying to get clarity on a few things and am looking for some info.
In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth.
But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. UNIX for Advanced & Expert Users
Hi,
If i want to write my data on several tapes, (more than one tape), what switch(s) i need to use with tar.
In other word if my data needs the sapce more than one tape & i don't wanna to compress or ... my data. so is it possible to write up to the end of the tape & it asks to put another... (1 Reply)
Discussion started by: nikk
1 Replies