Sponsored Content
Full Discussion: Linux and my cable modem
Top Forums UNIX for Dummies Questions & Answers Linux and my cable modem Post 9632 by PxT on Wednesday 31st of October 2001 10:55:18 AM
Old 10-31-2001
A DSL/Cable router is not going to help if the lan card is not working properly. You should get your network card functioning first. Make sure your card is supported (check the list of 3com cards here: http://www.linuxdocs.org/HOWTOs/Net-...54.html#AEN956). 'lsmod' may not list your ethernet card if the driver is compiled into the kernel. Check out the 'dmesg' command or look at the boot messages in /var/log/messages (or wherever Caldera puts them). You need to find out if the card was detected at boot-time.
 

10 More Discussions You Might Find Interesting

1. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies

2. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies

3. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies

4. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies

5. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies

6. UNIX for Dummies Questions & Answers

Installing Cable Modem on Irix Machine.

Ok I am new to this and wondering if there is any way of connecting a cable modem to an SGI that is running IRIX 6.5 and how to do it... (1 Reply)
Discussion started by: Acidjack
1 Replies

7. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created... (1 Reply)
Discussion started by: fnoyan
1 Replies

8. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

9. Solaris

Need help configuring Cable Modem on Solaris x86

I have a dual boot system with XP being the primary for now and Solaris 10 being the Secondary. I have a cable modem and wish to configure the same to be used with Solaris so that I can browse the Internet and such. I have connected my x86 machine with a Netgear Router and that in turn is... (7 Replies)
Discussion started by: tubbyrana
7 Replies

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 09:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy