Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Is anyone using unix with cable modem Post 9341 by PxT on Thursday 25th of October 2001 01:26:00 PM
Old 10-25-2001
Most companies wont officially support Unix. Its usually easy to get up and going. Just plug in the modem to your network card, use ifconfig or a dhcp client to setup your networking info and you are all set...
 

10 More Discussions You Might Find Interesting

1. IP Networking

cofiguring cable modem in red hat 7.1

It was easy in mandrake, but i don't know how in red hat. I have an Allied Telesyn AT2400/ET If it's possible in mandrake then i know it's possible in red hat. (5 Replies)
Discussion started by: walrus
5 Replies

2. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies

3. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies

4. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies

5. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies

6. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies

7. UNIX for Dummies Questions & Answers

Cable Modem, Unix, XP Computer Primary, need advice setup!

I have a XP computer which is my primary. I recently, well just today installed a old version of Mandrake Linux 6.5 I had laying on a self collecting dust on a old PII 233mhz that had to be vacummed out before I could use it. I have my XP computer connected by 10/100 NIC to a cable modem. My... (1 Reply)
Discussion started by: garfunkle
1 Replies

8. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created... (1 Reply)
Discussion started by: fnoyan
1 Replies

9. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies
BAYCOM(9)						      Kernel Reference Guide							 BAYCOM(9)

NAME
baycom - amateur (AX.25) packet radio network driver for baycom modems SYNOPSIS
#include <linux/baycom.h> #include <linux/hdlcdrv.h> DESCRIPTION
The driver currently supports three different modems: ser12, par96 and par97. ser12 This is a very simple 1200 baud AFSK modem. The modem consists only of a modulator/demodulator chip, usually a TI TCM3105. The computer is responsible for regenerating the receiver bit clock. The modem connects to a serial port, hence the name. Since the serial port is not used as an async serial port, the kernel driver for serial ports cannot be used, and this driver only supports standard serial hardware (8250, 16450, 16550). par96 This is a modem for 9600 baud FSK compatible to the G3RUH standard. The modem does all the filtering and regenerates the receiver clock. Data is transferred from and to the PC via a shift register. The shift register is filled with 16 bits and an interrupt is signalled. The PC then empties the shift register in a burst. This modem connects to the parallel port, hence the name. par97 This is a redesign of the par96 modem by Henning Rech, DF9IC. The modem is protocol compatible to par96, but uses only three low power ICs and can therefore be fed from the parallel port and does not require an additional power supply. IOCTL CALLS
The ioctl calls follow the implementation in the hdlcdrv. BAYCOMCTL_GETMODEMTYPE returns the modem type (i.e. ser12 or par96) and the options in effect (currently only the source of the DCD signal) BAYCOMCTL_SETMODEMTYPE sets the modem type and the options. Only superuser can do this. BAYCOMCTL_GETDEBUG return some debugging values. Not always available. SEE ALSO
baycom (9), soundmodem (9), linux/drivers/net/hdlcdrv.c, AUTHOR
baycom was written by Thomas Sailer, HB9JNX/AE4WA, (t.sailer@alumni.ethz.ch). Linux 2.1.x 2 October 1996 BAYCOM(9)
All times are GMT -4. The time now is 10:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy