Tape drive issues with SCO 5.0.5!!! Post: 93403

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Tape Drive SCO 5.0.7

Hi guys I had a system running 5.0.6 , we upgraded it to 5.0.7 everything was fine till i try to do a test backup. The error was cannot open (cannot open /dev/xct0 no such file or directory)what i did was, removed the tape , reboot the system and the try to install it again, but its...

2. UNIX for Dummies Questions & Answers

second tape drive on SCO 505

I need to run a back up that will take more than one tape. What is the command that will continue the back up on to a second tape drive. the first is /dev/rStp0 second is /dev/rStp1. Anyone?

3. UNIX for Dummies Questions & Answers

SCO 5.0.5 Tape Drive errors

hi guys, I.m trying to remove and add a new tape drive by using the mkdev tape command and when i try to update the Kernel this is what i'm getting, i386ld: Symbol Sdsk_no_tag in /var/opt/K/SCO/link/1.1.1Eb/etc/conf/pack.d/blad/s pace.o is multiply defined. First defined in...

4. SCO

SCO hard drive with data - No SCO computer

Situation - i have an IDE hard drive from server apparently running SCO last used in 2003. No access to computer it was formerly in. I need to access the drive to pull off data files from a billing/scheduling program. I have no SCO machine or access to one atm. Have some limited Linux...

5. SCO

SCO Openserver Release 5 and HP VS160 Tape Drive

Hi, Does anyone know if a HP VS160 Tape drive will work with SCO Openserver Release 5? If so what driver would it use? alad, cha? Thanks John

6. AIX

Tape Drive

I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How...

7. Solaris

Help with tape drive

Hey folks, Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes. I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V. As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly. ...

8. SCO

SCO 5.0.7 Tape Drive swap

Our tape drive died and I installed a newer Quantum DAT72 drive in it's place with the same SCSI ID. It still works, but with one major flaw, the system will lock up if I try to upgrade BackupEDGE or view NFS settings in scoadmin. I get a Transition to ready failure on ha=0* message when the...

LEARN ABOUT NETBSD

mlxctl

MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME

     mlxctl -- Mylex DAC960 family management utility

SYNOPSIS

     mlxctl [-f dev] [-v] [-a] status [drive] [...]
     mlxctl [-f dev] [-a] detach [drive] [...]
     mlxctl [-f dev] [-a] check [drive] [...]
     mlxctl [-f dev] rebuild channel:target
     mlxctl [-f dev] cstatus
     mlxctl [-f dev] rescan
     mlxctl [-f dev] config

DESCRIPTION

     The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices.

     The following options are available:

     -a       Apply the action to all drives attached to the controller.

     -f dev   Specify the control device to use.  The default is /dev/mlx0.

     -v       Increased verbosity.

     The following commands are available:

     cstatus  Display the controller's current status.

     status   Display the status of the specified drives.  This command returns 0 if all drives tested are online, 1 if one or more drives are
	      critical and 2 if one or more are offline.

     rescan   Re-scan the logical drive table, and attach or detach devices from the system as necessary.

     detach   Detach the specified drives.  Drives must be unmounted and unopened for this command to succeed.

     check    Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5).	This command returns imme-
	      diately.	The status command can be used to monitor the progress of the check.

     rebuild  Rebuild onto the specified physical drive.  Note that there can be only one running rebuild operation per controller at any given
	      time.  This command returns immediately.	The cstatus command can be used to monitor the progress of the rebuild.

     config   Write the current system drive configuration to stdout.

EXAMPLES

     Display the status of drive ld3 attached to the controller mlx1:

	   mlxctl -f /dev/mlx1 -v status ld3

SEE ALSO

     ld(4), mlx(4)

HISTORY

     The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD.

BUGS

     Modifying drive configuration is not yet supported.

     Some commands do not work with older firmware revisions.

     Error log extraction is not yet supported.

BSD
								  April 10, 2000							       BSD