11-11-2005
Thanks RTM. That's a new approach.
I'll give it a try and provide detail result if it fails.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
3. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
4. UNIX for Advanced & Expert Users
hi
I have a question,
eth0 : 192.168.2.10
eth1: 192.168. 2.11
subnet : 255.255.255.0
eth0 and eth1 plug same swich
I want communication between the two interface one host examp :
ping 192.168.2.10 -I eth1
ping 192.168.2.11 -I eth0
but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
LEARN ABOUT DEBIAN
rlm_detail
rlm_detail(5) FreeRADIUS Module rlm_detail(5)
NAME
rlm_detail - FreeRADIUS Module
DESCRIPTION
The rlm_detail module writes radius packets to 'detail' files. It is primarily used for storing accounting information, but can be used in
other sections to write packet details as well.
The file format is similar to that of the old Livingston servers, and many 'detail' file parsers should work with FreeRADIUS.
The main configuration items to be aware of are:
detailfile
The file name in which to store the radius packet records. NOTE: this variable is run through dynamic string expansion, and can
include FreeRADIUS variables to create a dynamic filename.
%{radacctdir}/%{Client-IP-Address}/detail-%Y%m
This will create one file per month, for each client.
This accomplishes 'file rotation' automatically from
within the server.
detailperm
The file permissions of the detailfile. If omitted, the default is 0600.
dirperm
The directory permissions of the directory where the detail files are created. The default is 0755.
locking
This option is set to 'yes' or 'no'. By default it is 'no'. Set this to yes to enable file locking, which is used with the
'radrelay' program.
CONFIGURATION
modules {
...
detail {
detailfile = %A/%{Client-IP-Address}/detail-%Y%m
detailperm = 0600
dirperm = 0755
locking = no
}
...
}
...
accounting {
...
detail
...
}
SECTIONS
authorization, accounting, pre_proxy, post_proxy, post_authentication
FILES
/etc/raddb/radiusd.conf
SEE ALSO
radiusd(8), radiusd.conf(5)
AUTHORS
Chris Parker, cparker@segv.org
5 February 2004 rlm_detail(5)