10-03-2005
i recently read a thing you posted on bboard.scifi.com and you said they discoverd a semi- aquatic antelope and gave its scientific name cetaformia anthalopus and that dosent exisit at all! that its remains were at berkeley museum of natural history and they have never heard of it. oh yea Dr. J. walden pond is not a person and defiently not a doctor and Khymer rouge dosent exist either also there is no Director of special collections named Dr. Stephanie Alderton. so you are a bull shiter and i hate you
10 More Discussions You Might Find Interesting
1. IP Networking
It was easy in mandrake, but i don't know how in red hat. I have an Allied Telesyn AT2400/ET
If it's possible in mandrake then i know it's possible in red hat. (5 Replies)
Discussion started by: walrus
5 Replies
2. IP Networking
If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies
3. UNIX for Dummies Questions & Answers
I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies
4. UNIX for Dummies Questions & Answers
Caldera eDesktop 2.4 - Cable Modem
my NIC card has been detected, but funny scenario:
#dmesg
eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef
/*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies
5. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
6. IP Networking
I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies
7. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
8. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
9. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
10. OS X (Apple)
Hi.
I have a very strange problem, so strange I don't even know which sub-forum to post it to.
Last week, my cable modem broke, so I took it back and got a new one.
The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet... (14 Replies)
Discussion started by: Scott
14 Replies
LEARN ABOUT CENTOS
history
history(n) Tcl Built-In Commands history(n)
__________________________________________________________________________________________________________________________________________________
NAME
history - Manipulate the history list
SYNOPSIS
history ?option? ?arg arg ...?
_________________________________________________________________
DESCRIPTION
The history command performs one of several operations related to recently-executed commands recorded in a history list. Each of these
recorded commands is referred to as an "event". When specifying an event to the history command, the following forms may be used:
[1] A number: if positive, it refers to the event with that number (all events are numbered starting at 1). If the number is negative,
it selects an event relative to the current event (-1 refers to the previous event, -2 to the one before that, and so on). Event 0
refers to the current event.
[2] A string: selects the most recent event that matches the string. An event is considered to match the string either if the string
is the same as the first characters of the event, or if the string matches the event in the sense of the string match command.
The history command can take any of the following forms:
history
Same as history info, described below.
history add command ?exec?
Adds the command argument to the history list as a new event. If exec is specified (or abbreviated) then the command is also exe-
cuted and its result is returned. If exec is not specified then an empty string is returned as result.
history change newValue ?event?
Replaces the value recorded for an event with newValue. Event specifies the event to replace, and defaults to the current event
(not event -1). This command is intended for use in commands that implement new forms of history substitution and wish to replace
the current event (which invokes the substitution) with the command created through substitution. The return value is an empty
string.
history clear
Erase the history list. The current keep limit is retained. The history event numbers are reset.
history event ?event?
Returns the value of the event given by event. Event defaults to -1.
history info ?count?
Returns a formatted string (intended for humans to read) giving the event number and contents for each of the events in the history
list except the current event. If count is specified then only the most recent count events are returned.
history keep ?count?
This command may be used to change the size of the history list to count events. Initially, 20 events are retained in the history
list. If count is not specified, the current keep limit is returned.
history nextid
Returns the number of the next event to be recorded in the history list. It is useful for things like printing the event number in
command-line prompts.
history redo ?event?
Re-executes the command indicated by event and returns its result. Event defaults to -1. This command results in history revision:
see below for details.
HISTORY REVISION
Pre-8.0 Tcl had a complex history revision mechanism. The current mechanism is more limited, and the old history operations substitute and
words have been removed. (As a consolation, the clear operation was added.)
The history option redo results in much simpler "history revision". When this option is invoked then the most recent event is modified to
eliminate the history command and replace it with the result of the history command. If you want to redo an event without modifying his-
tory, then use the event operation to retrieve some event, and the add operation to add it to history and execute it.
KEYWORDS
event, history, record
Tcl history(n)