09-07-2005
rpcinfo shows that nfs works woth tcp
I used the rpc -p localhost and it shows that nfs is working with tcp.
any other ideas? please?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
2. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
3. Solaris
We are installing Solaris 9 with Jumpstart ...facing problems..
Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly.
when we give "boot net - install" at OK prompt, it is coming till
"The system is coming up. Please wait"
After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies
4. Solaris
Hi Everyone,
Thanks in advance for reading my thread. I am not very familiar with Unix so please bear with me if I say anything stupid.
I have a SunFire V100 server with Solaris 8, which I made into a Boot/Install/Profile server. Recently, I re-install the V100 box with Solaris 10.
The... (5 Replies)
Discussion started by: cityshrimp
5 Replies
5. Solaris
Hi,
I build a jumpstart server with a running dhcp server. I already managed to install a x86 client via network. But my sparc clients aren't still working.
When booting via network I get the following message:
Timeout waiting for ARP/RARP packet
I ran "snoop" on the server:
client2 ->... (1 Reply)
Discussion started by: Jay_Fisi
1 Replies
6. Solaris
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What... (1 Reply)
Discussion started by: Pratik Gharti
1 Replies
7. Solaris
Hi,
I have a V240 Solaris 10 (06.06) with a Solaris image of 08.07 (newest release). On the jumpstart server I have also installed JET for testing.
Client was setup using the JET utilities.
jade = jumpstart server
phoebus = client (MAC: 0:3:ba:9e:6f:2d IP:192.168.58.121 )
When I now... (0 Replies)
Discussion started by: Ironhead
0 Replies
8. Solaris
Hello,
I did this perfectly fine with S10Update3. But with S10Update4 something is strange
a) For some reason when I am moving to Update 4, it keeps prompting for name service etc etc. But this goes away if I give nfs4_domain=dynamic in the sysidcfg file. This was not happening for Update3. Any... (1 Reply)
Discussion started by: Naanu
1 Replies
9. Solaris
I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output
bash-3.2# cat sysidcfg
terminal=vt100
network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \
protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
10. Solaris
A simple question about nfs and jumpstart
,i setup server (all on linux)
tftp ok # boot and reach menu grub,and start
nfs not ok
i did
/export/solaris 192.168.0.0/24(ro,no_root_squash,anonuid=0,anongid=0)
and on solaris i put config with sysidcfg,profile,etc
When solaris boot from net it... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT OSX
rpc.svcgssd
rpc.svcgssd(8) System Manager's Manual rpc.svcgssd(8)
NAME
rpc.svcgssd - server-side rpcsec_gss daemon
SYNOPSIS
rpc.svcgssd [-n] [-v] [-r] [-i] [-f] [-p principal]
DESCRIPTION
The rpcsec_gss protocol gives a means of using the gss-api generic security api to provide security for protocols using rpc (in particular,
nfs). Before exchanging any rpc requests using rpcsec_gss, the rpc client must first establish a security context with the rpc server.
The linux kernel's implementation of rpcsec_gss depends on the userspace daemon rpc.svcgssd to handle context establishment on the rpc
server. The daemon uses files in the proc filesystem to communicate with the kernel.
OPTIONS
-f Runs rpc.svcgssd in the foreground and sends output to stderr (as opposed to syslogd)
-v Increases the verbosity of the output (can be specified multiple times).
-r If the rpcsec_gss library supports setting debug level, increases the verbosity of the output (can be specified multiple times).
-i If the nfsidmap library supports setting debug level, increases the verbosity of the output (can be specified multiple times).
-p Use principal instead of the default nfs/FQDN@REALM.
-n Use the system default credentials (host/FQDN@REALM) rather than the default nfs/FQDN@REALM.
SEE ALSO
rpc.gssd(8),
AUTHORS
Dug Song <dugsong@umich.edu>
Andy Adamson <andros@umich.edu>
Marius Aamodt Eriksen <marius@umich.edu>
J. Bruce Fields <bfields@umich.edu>
12 Jan 2007 rpc.svcgssd(8)