08-05-2005
null modem
Hi,
i don;t have any keyboard attached to sun ultra ent 3000.
i used a cable modem, but i am not sure it is the right cable..
i am using this cable to connect from pc(com1 or com2, DB9, female) to modem (DB25,male) for dialup connection to internet.
is it the right cable?
i try teraterm and set it to com1, baudrate 9600, xon/xoff or hardware, but nothing come up in teraterm windows...
i put db25 on port A Sun server.
please help...
thanks
10 More Discussions You Might Find Interesting
1. IP Networking
If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies
2. UNIX for Dummies Questions & Answers
I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies
3. UNIX for Dummies Questions & Answers
Caldera eDesktop 2.4 - Cable Modem
my NIC card has been detected, but funny scenario:
#dmesg
eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef
/*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies
4. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
5. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
6. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
7. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
8. Solaris
hi all..
sorry for repeating the same question many times,
i just set up a null modem, i am using this as reference :
DB25 DB9
-- -
2 TD ---- 2 RD
3 RD ---- 3 TD
4 RTS ---- 8 CTS
5 CTS ---- 7 RTS
7 GND ---- 5 GND
6 DSR -+
+--- 4 DTR
8... (0 Replies)
Discussion started by: waterbear
0 Replies
9. Solaris
Hi Gurus,
Can I use null modem cable in Ultra sparc 10 workstation
Thanks (3 Replies)
Discussion started by: kumarmani
3 Replies
10. Hardware
Hello,
I want to connect a VT520 terminal to p3 linux box.
I have two questions regarding the connection. First,
is it possible to use RJ45 instead of RS232
cable. (with DB9 pin to RJ45 and DB25 to RJ45 converter).
Second point is that; do i need null modem cable or
straight cable... (5 Replies)
Discussion started by: vectrum
5 Replies
LEARN ABOUT DEBIAN
liebert
LIEBERT(8) NUT Manual LIEBERT(8)
NAME
liebert - Driver for Liebert contact-closure UPS equipment
NOTE
This man page only documents the hardware-specific features of the liebert driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
This driver supports some Liebert UPS equipment with a contact-closure interface. This includes the UPStation GXT2 with their
contact-closure cable. The smart mode ("Multilink") cable is not supported by this driver.
EXTRA ARGUMENTS
This driver does not support any extra settings in the ups.conf(5).
BUGS
This driver does not yet support shutdowns by raising DTR. Be aware that shutdowns are not possible with the stock contact-closure cable.
You may have to build another cable with DTR connected through to the UPS for it to work.
There is no way for this driver to detect the hardware or cable. It will start up successfully even if no UPS is present. This is a
fundamental limitation of any contact-closure driver.
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 LIEBERT(8)