Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Quad Fast Ethernet Card on Sparc 10?
Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10? Post 7854 by jskillet on Tuesday 2nd of October 2001 04:53:21 PM
Old 10-02-2001
Question Quad Fast Ethernet Card on Sparc 10?
I am having a problem getting my configuration to stick. After I installed my quad-card I did the following:

1. created hostname.qe0, hostname.qe1, hostname.qe2, hostname.qe3 files in my /etc directory.

2. In my /etc/hosts file I added the ip address of each interface and the name for each interface :
216.32.55.67 ext
65.3.2.1 dmz
10.10.10.1 int
172.1.1.1 net

3. In each hostname.qe file I added the hostname associated with each interface.

4. From a terminal I did the following:
ifconfig qe0 216.32.55.67 up
ifconfig qe1 65.3.2.1 up
ifconfig qe2 10.10.10.1 up
ifconfig qe3 172.1.1.1 up


***After I do all this it works fine

~~~Once I reboot my machine....it loses all of the settings for the Quad-Card.

Have any of you ever run into this or am I doing anything noticibly
wrong? Any help on this would be great.

Thanks,
Jeff
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

5. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:... (5 Replies)
Discussion started by: hshapiro
5 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the... (2 Replies)
Discussion started by: freddie50
2 Replies

LEARN ABOUT MINIX

reboot

REBOOT(8)						      System Manager's Manual							 REBOOT(8)

NAME

       reboot - reboot the system immediately

SYNOPSIS

       reboot [-f]

DESCRIPTION

       Reboot  can  be	used  to  reboot  the  system  after  installing a new kernel.	It does not inform the users, but does log it's actions in
       /usr/adm/wtmp and /usr/adm/authlog.  The system is then rebooted with the reboot(2) systemcall.

       If the -f flag is not given then all processes are sent terminate signals to give them a chance to die peacefully before the reboot() call.

       If the wtmp file exists, reboot logs itself as if it were a shutdown.  This is done to prevent last(1) from talking  about  system-crashes.
       Reboot is registered as is in the authlog file.

       Reboot can only be executed by the super-user.  Any other caller will be refused, either by reboot(8) or by reboot(2).

SEE ALSO

       reboot(2), shutdown(8), halt(8), boot(8).

BUGS

       The  error message's given by reboot are not always useful.  There are several routines that can fail, but which are not fatal for the pro-
       gram.

AUTHOR

       Edvard Tuinder (v892231@si.hhs.NL)

																	 REBOOT(8)
All times are GMT -4. The time now is 07:53 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy