06-27-2005
prtdiag will show all of the I/O cards. However the precise format varies from system to system. On an Enterprise 420R, an hme card shows up with "network-SUNW,hme" on the line. No so with an Ultra 2. There we just get "SUNW,hme". This issue also prevents "grep network /etc/path_to_inst" which might otherwise look promising. It might be that this works with PCI bus systems and fails with Sbus systems, but I'm not sure. But then again, Sun has other buses.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
3. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
4. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
5. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
6. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
7. Programming
Hello
I have a problem with retreiving network interface list using IOCTLs. I have 4 interfaces:
$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope... (1 Reply)
Discussion started by: xyzt
1 Replies
8. Hardware
Hello everybody,
I'm having troubles with Slackware 13.1 and network cards.
I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the... (5 Replies)
Discussion started by: semash!
5 Replies
9. UNIX for Dummies Questions & Answers
Hi All,
I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They... (0 Replies)
Discussion started by: jackma
0 Replies
10. Solaris
Hello All
I am trying to get a list of process or applications runninging on the network only. I should emphasize that im not interested in the application or process if its not using the network.
I tried the good old netstat comand, but im not able to figure out how to list the running... (8 Replies)
Discussion started by: busi386
8 Replies
HME(4) BSD Kernel Interfaces Manual HME(4)
NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device hme
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_hme_load="YES"
DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.
All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.
HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.
Cards supported by the hme driver include:
o Sun PCI SunSwift Adapter (``SUNW,hme'')
o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')
NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
add-on cards except the single-port SBus versions.
SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)
Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996,
http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf.
HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0.
AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.
BSD
June 14, 2009 BSD