06-25-2005
Yes, you can find the 66MHz slots on sunsolve.
Also, what are you using for volume management? If using Veritas Volume Manager, there is no need to worry about the controller numbers changing.
If using Sun Disk Suite, I think you will have problems.
10 More Discussions You Might Find Interesting
1. BSD
Hi!
I just wanted to know what network cards are supported in FreeBSD. I have looked at the list of supported cards but I can't find any of them in the stores. Is the list not updated, I would really preciate info about where (in EU, Sweden) I can buy them.
/Peter (2 Replies)
Discussion started by: Barfly.se
2 Replies
2. Solaris
Hi all,
I have a compatibly issues with a new hardware
My config is the following one :
Solaris 10
V490 Hardware
2 X HBA Qlogic 2310f cards
An HP EVA 5000 for storage ...
Veritas VxVM 4.1 MP1
When I reboot my server, VxVM is trying to mount/use the volume before it's... (0 Replies)
Discussion started by: unclefab
0 Replies
3. Solaris
Due to speed mismatch, the server kept crashing. Sun suggests that I need to move the two HBA cards from the 66Mhz to the 33Mhz slots. There are tons of disks that are connected to these HBAs and I have Veritas volume manager.
Does anyone have a list of what I need to do prior/after moving to... (3 Replies)
Discussion started by: kiem
3 Replies
4. Solaris
I've got lots of scsi transport errors on the E2900 - the HBA was replaced once out of curiosity but the problem still exists.
Feb 15 07:03:11 ivsdbch2 scsi: WARNING: /ssm@0,0/pci@18
,600000/SUNW,jfca@1,1/fp@0,0/ssd@w5005076300c889cb,4 (ssd21):
Feb 15 07:03:11 ivsdbch2 SCSI transport... (1 Reply)
Discussion started by: kiem
1 Replies
5. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
6. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
7. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
8. Solaris
I'm looking for open PCI slots in our array of sun boxes. I need help on how to distinguish if there's an open slot or not using prtdiag and prtconf. Is there a better tool for this? TIA.
Here's my prtdiag -v | grep pci:
pci 66 PCI5 SUNW,qlc-pci1077,2312 (scsi-+
... (9 Replies)
Discussion started by: revzalot
9 Replies
9. BSD
Hi,
The title is a bit misleading, but it seems I can't re-edit the title after creating the post - apologies.
I have been handed a variety of servers, whereas quite a few of these are older FreeBSD (4.8, thank you legacy). I now have one of these servers which has a HBA card installed, and... (0 Replies)
Discussion started by: brightstorm
0 Replies
10. Solaris
How do I find any available PCI slots on a v440?
When I run prtconf, I get the following output? But I am not able to make out whether all the PCI slots are used.
================================= IO Devices =================================
Bus Freq
Brd Type MHz Slot ... (1 Reply)
Discussion started by: jtamminen
1 Replies
LEARN ABOUT HPUX
vgrestore
vgrestore(1M) vgrestore(1M)
NAME
vgrestore - restore a VxVM disk group back to an LVM volume group
SYNOPSIS
/etc/vx/bin/vgrestore vg_name
DESCRIPTION
The vgrestore command restores a Logical Volume Manager (LVM) volume group that was previously converted to a VxVM disk group by the vxvm-
convert utility.
ARGUMENTS
vg_name
Specifies the name of a volume group that was converted to a VxVM disk group by the vxvmconvert utility.
EXIT CODES
vgrestore exits with one of the following values:
0 Successful completion.
>0 Failure; an error occurred.
WARNINGS
vgrestore functions only on VxVM disk groups that were converted from LVM volume groups by the vxvmconvert command.
It is a good idea to back up user data before running vgrestore, and restore it after the vgrestore completes, as vgrestore can only
restore a logical volume back to the state it was in before conversion to VxVM. If data changed on the volume while it was a VxVM volume,
the changes won't be reflected on the volume after being restored to LVM.
As part of the original conversion process, applications that once referenced the now-converted LVM volume's path names may have changed to
reference VxVM volume special device file names. Alternatively, special device file path names originally representing the now-converted
LVM volumes may have changed to symbolic links pointing to the VxVM volume path names. Be sure to undo these actions when restoring back
to LVM.
Do not use vgrestore unless you are certain that you want to restore LVM volume groups. After vgrestore this is run, the VxVM disks will
no longer exist.
EXAMPLES
To restore the LVM volume group vg03 that was converted by vxvmconvert to the VxVM disk group dg03, enter:
vgcfgrestore vg03
SEE ALSO
vxvmconvert(1M)
Veritas Volume Manager Migration Guide
VxVM 5.0.31.1 24 Mar 2008 vgrestore(1M)