06-23-2005
Use smitty tcpip -> further config -> static routes -> remove static route
10 More Discussions You Might Find Interesting
1. IP Networking
I have a Unix box with 2 network interfaces on the same IP subnet and would like to add a host route via a specific interface. Any assistance would be greatly appreciated. (3 Replies)
Discussion started by: diemos
3 Replies
2. Debian
Ok, I made changes to my routing tables..... which file do I modify to make the routes initialize correctly when the machine boots up? I work with all flavours of Unix/Linux... but this is an older box...
Linux, Release 2.2.14-5.0.
I did a grep for the default route in /etc, but didnt find... (2 Replies)
Discussion started by: djsal
2 Replies
3. SCO
Hi,
I add following routes manually each time system reboots:
#route add 192.168.1.0 -gateway 192.168.0.90
#route add 192.168.200.0 -gateway 192.168.0.200
Is there any way in SCO 7.1.1 to automate this route add process? i.e. each time system reboots, it automatically adds these routes in... (1 Reply)
Discussion started by: tayyabq8
1 Replies
4. Solaris
Hi there
When adding a route (or indeed deleting a route) which file is amended ? I am moving a box from one network to another and when it starts up it tries to connect run 'add net 192.x.x.x' etc etc ...but i dont want it to do that
where do I edit these route additions
cheers (5 Replies)
Discussion started by: hcclnoodles
5 Replies
5. Solaris
Solaris Guru's
What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost.
I understand the /etc/defaultrouter for the default router
and the <route add> command but using this command routes will be removed once the node reboots.
Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies
6. AIX
I added a static route through smit using:
Communications applications and Services ==>
TCIP/IP ==>
Further Configuration ==>
Static Routes ==>
Add a Static Route ==>
Route Type of host
Filled in Destination Address, Default Gateway Address and Network Interface of en0.
This... (2 Replies)
Discussion started by: jyoung
2 Replies
7. UNIX for Dummies Questions & Answers
Hello,
I have two AIX 5.3 servers that are supposedly set up exactly the same. The problem I am having is on one of the servers, it seems dynamic routes are being added mysteriously and non-periodically. This only happens on one server and not the other. Also, there doesn't seem to be a specific... (1 Reply)
Discussion started by: Conutmonky
1 Replies
8. IP Networking
I would really appreciate some help with HP UX's Network Routes.
Basically, what I want to do is, I would want a system with global ip (eg: 202.144.138.122) to ping/access my HP-UX server which is with private IP address (192.168.1.23). I have all the routers/switches in between properly route... (2 Replies)
Discussion started by: damchey
2 Replies
9. SCO
Hi,
Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies
10. Solaris
Hello All,
I have a Solaris 10 machine with 4 physical network interfaces configured viz. igb0, e1000g0, igb2 and e1000g2.
Out of these interfaces, I am routing all my normal monitoring and O&M activities via. igb0 and e1000g0 interfaces.
However, I am facing an issue on one of the... (4 Replies)
Discussion started by: mystition
4 Replies
NRPARMS(8) Linux System Managers Manual NRPARMS(8)
NAME
nrparms - Configure the NET/ROM interface.
SYNOPSIS
nrparms -nodes node +|- ident quality count port neighbour [digicall...]
nrparms -routes port nodecall [digicall...] +|- quality
nrparms -version
DESCRIPTION
This program is used to manipulate the routing tables of the NET/ROM network layer, or to get and set many of the network and transport
layer parameters for the NET/ROM protocol. The program has three basic modes of operation, node setting, neighbour setting and general
parameter setting. The syntax for the node and neighbour setting is taken from the original NET/ROM manual and is therefore not very UNIXy
but should be familiar to those familiar with NET/ROMs or TheNet.
To set up a new route to a NET/ROM node in the routing tables you must use the nodes option. All of the parameters are needed to add the
node. It is probably best to illustrate with an example:
nrparms -nodes GB7BPQ + NMCLUS 120 6 vhf G8ROU-3
This creates a new route to a distant node with the callsign GB7BPQ and the alias NMCLUS, it has a quality of 120 (out of 255) and has an
obsolescence count of six and packets for that node should be sent on the AX.25 port named vhf to my immediate neighbour G8ROU-3. The call-
signs of the node and the neighbour may be the same. For example to set up the node G8ROU-3 which is also my immediate neighbour, I would
use:
nrparms -nodes G8ROU-3 + MATLCK 200 6 vhf G8ROU-3
If the ident of the remote node is not known, it is possible to add a node with a blank ident. To do this an ident of '*' must be entered
on the command line. Because of the command line expansion that shells do, the * must be escaped by enclosing it in quotes.
It is also possible to remove a route to a distant node with the same command except that the + is replaced by a -. The other parameters
must also be present. If the node has not other routes then the node will be deleted, and the neighbour node that the connections go via
may also be deleted if no other node route uses it, and it is not a locked neighbour entry.
When setting up a new node, a new neighbour entry may also be created. This will have a default value. For that neighbour to be meaningful
in the automatic routing process, it must have a more reasonable entry in the neighbours list. To do this the routes option of the command
must be used. An example:
nrparms -routes ax0 G8ROU-3 + 120
This will create (or update) the neighbour entry for G8ROU-3 with a quality of 120 and it will be locked, it will not create a node entry
for the neighbour. This quality will be used by the netromd(8) program when calculating route qualities via this neighbour. Normally once a
neighbour has zero node routes going via it, it will be deleted. Locking a neighbour prevents the deletion from occurring. To unlock a
neighbour entry, the same command is used but with the + replaced by a -.
FILES
/etc/ax25/axports
/etc/ax25/nrports
SEE ALSO
call(1), netrom(4), nrports(5), axparms(8), netromd(8), nrparms(8).
AUTHOR
Jonathan Naylor G4KLX <g4klx@g4klx.demon.co.uk>
Linux 25 January 1997 NRPARMS(8)