Apache Question - Securing against unwanted use with cable modem Post: 71172

10 More Discussions You Might Find Interesting

1. IP Networking

cofiguring cable modem in red hat 7.1

It was easy in mandrake, but i don't know how in red hat. I have an Allied Telesyn AT2400/ET If it's possible in mandrake then i know it's possible in red hat.

2. IP Networking

unix and the cable modem

If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that...

3. UNIX for Dummies Questions & Answers

Linux and my cable modem

I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now?

4. UNIX for Dummies Questions & Answers

can't get my cable modem up

Caldera eDesktop 2.4 - Cable Modem my NIC card has been detected, but funny scenario: #dmesg eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef /*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module....

5. UNIX for Dummies Questions & Answers

Is anyone using unix with cable modem

Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how. Thank you for all your help.

6. IP Networking

DHCP Linux and cable modem

I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how...

7. UNIX for Dummies Questions & Answers

cable modem to sparc

hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem , i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how...

8. BSD

cable modem problem

hi I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system. When I type, I get # ifconfig -a lo0 : .... ... ... rl0 : .... ... ... vr0 : ... ... ... I have two network cards (the machine will be a router). I created...

9. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks

10. OS X (Apple)

Cannot access UNIX.com with new cable modem

Hi. I have a very strange problem, so strange I don't even know which sub-forum to post it to. Last week, my cable modem broke, so I took it back and got a new one. The new one doesn't work with my old router so, for now, I have to connect the modem directly to my Mac with an ethernet...

LEARN ABOUT DEBIAN

gnunet-nat-server

GNUNET-NAT-SERVER(1)					      General Commands Manual					      GNUNET-NAT-SERVER(1)

NAME

       gnunet-nat-server - help GNUnet setup test network setup with NAT

SYNOPSIS

       gnunet-nat-server [options] PORT

DESCRIPTION

       Normal  GNUnet end-users should not concern themselves with gnunet-nat-server.  In fact, distributions are encouraged to consider not ship-
       ping it at all.	Running gnunet-nat-server's is similar to running hostlist servers: it is a special service to the community with  special
       requirements and no benefit to those running the service.

       This  program  will listen on the specified PORT for incoming requests to test a peer's network connectivity.  Incoming requests can ask it
       to connect to a given IPv4 address (and port) using TCP or UDP and to send a 2-byte test message using the specified address.  The  program
       can  also  be asked to send a "fake" ICMP response message to a given IPv4 address (for autonomous NAT traversal --- see the description in
       the respective research paper).

       The idea is that gnunet-nat-server will be run on some trusted hosts with unrestricted connectivity to allow GNUnet  users  to  test  their
       network	configuration.	 As  written, the code allows any user on the Internet to cause the gnunet-nat-server to send 2-bytes of arbitrary
       data to any TCP or UDP port at any address.  We believe that this is generally harmless.

       When running gnunet-nat-server, make sure to use a configuration that disables most NAT options but enables  'enable_nat_client'  and  sets
       'internal_address'  to  the  global  IP address of your local host.  Also, the gnunet-helper-nat-client should be installed locally and run
       with root privileges (SUID), otherwise the gnunet-nat-server will not work properly.

       Note that gnunet-nat-server could be run via gnunet-arm but typically is not.  Also, the name of the host and port  that  gnunet-nat-server
       is  run on should be specified in the NATSERVER option in the [setup] section of the configuration file of hosts that are supposed to auto-
       configure with this server.

OPTIONS

       -c FILENAME,  --config=FILENAME
	      Use the configuration file FILENAME.

BUGS

       Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>

SEE ALSO

       gnunet-transport(1)

GNUnet								    25 Feb 2012 					      GNUNET-NAT-SERVER(1)