Sponsored Content
Special Forums IP Networking unable to bring up any interface Post 6978 by alam on Monday 17th of September 2001 09:16:08 AM
Old 09-17-2001
Question unable to bring up any interface

I have Linux 7.1 setup on a Dell and am unable to bring up any interfaces. Both the lo and eth0 fail upon boot up and I get a insmod error possibly due to bad irq or IO setting.
If I disable eth0 upon boot, then lo works fine, but offcourse I get the "delaying initialization" upon boot for eth0
help
thanks

Last edited by alam; 09-17-2001 at 11:09 AM..
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Unable to bring up Sun OS

The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the... (2 Replies)
Discussion started by: mayewil
2 Replies

2. Solaris

Unable to bring a disk from error to online state.

Hello experts. I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format. Commands i used and output are.... #vxdisk list DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies

3. IP Networking

Unable to start network interface

Hi (sorry for my bad English) I'm trying to configure an US Robotics (USR5423) wirless usb adapter on Fedora 9. the device is detected, and i'm trying to configure a wireless connection. When I want to activate the device using #service network restart or # /etc/init.d/network restart... (0 Replies)
Discussion started by: teis
0 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

6. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

7. Solaris

Unable to bring iscsitgt service to online

this is samiulla in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance and i am unable to bring into online with svcadm clear iscsitgt how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies

8. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
IPSEC_TNCFG(8)							Executable programs						    IPSEC_TNCFG(8)

NAME
ipsec_tncfg - manipulate KLIPS virtual interfaces SYNOPSIS
ipsec tncfg ipsec tncfg --create virtual ipsec tncfg --delete virtual ipsec tncfg --attach --virtual virtual --physical physical ipsec tncfg --detach --virtual virtual ipsec tncfg --clear ipsec tncfg --version ipsec tncfg --help KLIPS
Note that tncfg is only supported on the KLIPS stack which uses ipsecX interfaces bound to physical interfaces DESCRIPTION
The purpose of tncfg is to attach/detach IPsec virtual interfaces (e.g. ipsec0) to/from physical interfaces (e.g. eth0) through which packets will be forwarded once processed by KLIPS. When using the MAST stack, tncfg is used to create and delete virtual interfaces known as mastXXX. mast stands for Mooring and XXX. The form with no additional arguments lists the contents of /proc/net/ipsec_tncfg. The format of /proc/net/ipsec_tncfg is discussed in ipsec_tncfg(5). The --attach form attaches the virtual interface to the physical one. The --detach form detaches the virtual interface from whichever physical interface it is attached to. The --clear form clears all the virtual interfaces from whichever physical interfaces they were attached to. Virtual interfaces typically have names like ipsec0 or mast0 while physical interfaces typically have names like eth0 or ppp0. EXAMPLES
ipsec tncfg --create mast12 creates the mast12 device. ipsec tncfg --create ipsec4 creates an ipsec4 device, but does not attach it. ipsec tncfg --attach --virtual ipsec0 --physical eth0 attaches the ipsec0 virtual device to the eth0 physical device. FILES
/proc/net/ipsec_tncfg, /usr/local/bin/ipsec SEE ALSO
ipsec(8), ipsec_manual(8), ipsec_eroute(8), ipsec_spi(8), ipsec_spigrp(8), ipsec_klipsdebug(8), ipsec_tncfg(5) HISTORY
Written for the Linux FreeS/WAN project <http://www.freeswan.org/> by Richard Guy Briggs. AUTHOR
Paul Wouters placeholder to suppress warning libreswan 12/16/2012 IPSEC_TNCFG(8)
All times are GMT -4. The time now is 09:42 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy