12-03-2004
maybe:
write: modconf and you should search drivers for your card and add to kernel, and you shut off other cards. maybe is a collision.
cU
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
learn(1) General Commands Manual learn(1)
NAME
learn - Provides computer-aided instruction for the C shell
SYNOPSIS
learn [-directory] [subject] [lesson]
The learn command provides computer-aided instruction courses and practice in the use of Tru64 UNIX.
OPTIONS
Allows you to exercise a script in a nonstandard place.
DESCRIPTION
To get started, enter learn; if this is the first time that you are invoking the learn command, you are guided through a series of ques-
tions to determine what type of instruction you want to receive.
If you have used learn before and left your last session without completing a subject, the program uses information in $HOME/.learnrc to
start you up in the same place you left off.
To bypass questions, enter a subject or lesson. In order to enter a lesson, you must know the lesson number that you received in a previ-
ous learn command session. If you do not know the lesson number, enter the lesson number as a subject. The learn command searches for the
first lesson containing the subject you specified. If the lesson is a - (dash), learn prompts for each lesson; this is useful for debug-
ging.
You can specify the following subjects:
files editor vi morefiles macros eqn C
SUBCOMMANDS
There are a few special commands. The bye command terminates a learn session, and the where command tells you of your progress (where m
tells you more.) The again command redisplays the text of the lesson and again lesson lets you review lesson. The hint command prints the
last part of the lesson script used to evaluate a response, while hint m prints the entire lesson script. This is useful for debugging
lessons and might possibly give you an idea about what is expected.
EXAMPLES
To take the online lesson about files, enter: learn files
You are then prompted for further input.
FILES
Playpen directories. Start-up information.
SEE ALSO
Commands: csh(1), ex(1)
learn(1)