12-03-2004
maybe:
write: modconf and you should search drivers for your card and add to kernel, and you shut off other cards. maybe is a collision.
cU
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT REDHAT
cardmgr
CARDMGR(8) System Manager's Manual CARDMGR(8)
NAME
cardmgr - PCMCIA device manager
SYNOPSIS
cardmgr [-V] [-q] [-d] [-o] [-f] [-v] [-c configpath] [-m modpath] [-p pidfile] [-s stabfile]
DESCRIPTION
Cardmgr monitors PCMCIA sockets for card insertion and removal events. When a card is inserted, cardmgr looks up the card in a database of
known cards. If the card can be identified, appropriate device drivers will be loaded and bound to the card. When a card is ejected, that
card's drivers will be shut down and unloaded if possible. Based on the contents of the PCMCIA card configuration database, cardmgr may
also execute arbitrary commands when appropriate cards are either inserted or removed.
All insertion and removal events, device driver loads and unloads, and startup and shutdown commands are reported in the system log file.
Warnings and errors will also be logged. Current card and device information for each socket is recorded in /var/lib/pcmcia/stab.
Normally, when a card is identified, cardmgr will send a beep to the console. A beep is also generated when a card is successfully config-
ured. A beep of lower pitch is generated if either of these steps fails. Ejecting a card produces a single beep.
When cardmgr receives a SIGHUP signal, it will reload its configuration file. When cardmgr receives a SIGTERM signal, it will shut down
all sockets that are not busy and then exit, but drivers for busy sockets will stay loaded.
If the PCMCIA_OPTS environment variable is set, its contents will be parsed after the main card configuration file is read.
At startup, cardmgr requires that /tmp reside on a filesystem that permits special device files (i.e., a real linux filesystem, that is not
mounted "nodev").
OPTIONS
-V Show version information and exit.
-q Quiet mode: don't beep when cards are inserted.
-v Verbose mode: generates more informational messages during normal operation. Configuration scripts are executed with VERBOSE=y.
-d Follow module dependencies when loading driver modules, by defaulting to use modprobe instead of insmod. Normally, cardmgr will try
using modprobe only after an unsuccessful attempt with insmod.
-f Foreground: do not fork and run as a daemon until after configuring any cards that are already present.
-o One pass: configure cards that are present, then exit. This flag also forces cardmgr to run in the foreground.
-c configpath
Look for the card configuration database and card configuration scripts in the specified directory, instead of /etc/pcmcia.
-m modpath
Look for loadable kernel modules in the specified directory, instead of /lib/modules/`uname -r`.
-p pidfile
Write the PID of the cardmgr process to the specified file, instead of /var/run/cardmgr.pid.
-s stabfile
Write current socket information to the specified file, instead of /var/lib/pcmcia/stab.
FILES
/etc/pcmcia/config Card configuration database
/etc/pcmcia/config.opts Local resource settings for PCMCIA devices
/var/run/cardmgr.pid PID of active cardmgr process
/var/lib/pcmcia/stab Current card and device information for each socket.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
pcmcia(5), stab(5), cardctl(8), cardinfo(1).
pcmcia-cs 2001/07/19 23:41:34 CARDMGR(8)