09-20-2004
Some software requires the 64 bit kernel mode and on Intel it runs the 32 bit mode.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Pls help
i've used the boot assistance disk to boot my computer (P3 300)
after checking the drivers , i select the CD to install , however,
the computer said it can't mount the CD
CD is download from sun.com (solaris 8)
my CD rom is Misabushi and Ricoh (7060) ,
both cannot do so,
what is... (4 Replies)
Discussion started by: kazamih
4 Replies
2. UNIX for Dummies Questions & Answers
i am looking for video drivers for a hercules stingray 128/3d card running on an HP vectra with solaris i386 version 7. can anyone point me to a download? (1 Reply)
Discussion started by: thomasaowens
1 Replies
3. IP Networking
I have just installed solaris 8 for Intel on one of my machines at home and I have a cable modem connection with a static IP and I am using a linksys cable/dsl router to assign IP's to my machines. I was wondering if any of you guys know the specific files and examples of the files I have to... (2 Replies)
Discussion started by: reggie316
2 Replies
4. UNIX for Advanced & Expert Users
hi.
Have anyone use kde for solaris, if so can you help me download and configure it. i don't know which files i should download for solaris because there lots of files. Could you point me to the right path.thanks in advance. (9 Replies)
Discussion started by: souldier
9 Replies
5. Programming
hi I'm looking for a C Compiler that will run on a Solaris 8 (Intel) platform and that doesn't need to be complied.
I've tried gcc binaries but they don't seem to work.
Thanx. (5 Replies)
Discussion started by: ianf
5 Replies
6. UNIX for Dummies Questions & Answers
Do you now have to pay to download the Solaris 8 OE? If so when did they change it? (3 Replies)
Discussion started by: tycobb
3 Replies
7. Solaris
Hi im trying to install solaris 9 Intel and when i insert the installation cd, i run threw all the steps and when it goes and configure the system it fails with this error
cannot mount root on /pci@0,0/pci-ide@2.1/ide@1/sd@0,0"a fstype ufs
panic/thread=fec29020" vfs_mountroot: cannot mount... (1 Reply)
Discussion started by: dennisca
1 Replies
8. Solaris
Hello all mentor.
I am a new in this furom and also just self studying unix environment. :confused:
I have installed intel solaris 9 in my laptop and i have forgotten the root password nor maybe the numlock or capslock of the keyboard was enabled
during I enter the password installation... (3 Replies)
Discussion started by: eykyn17
3 Replies
9. Solaris
Hi All,
How can I go to OBP on Solaris 10-intel? I tried doing ctrl+c or ctrl+break, it won't go to the "ok" prompt.
Thanks in advance,
itik (6 Replies)
Discussion started by: itik
6 Replies
10. Solaris
just need help with loading solaris 10 from cds that i bought from sun. i have a dell box that had solaris 8 on it, wiped it and stuck in the cd1 for solaris 10. selected "solaris" for install. went through a few minutes then comes up with"sunOS Release 5.10 version generic_137138-09 32-bit,... (3 Replies)
Discussion started by: flir11
3 Replies
LEARN ABOUT DEBIAN
kbdrate
KBDRATE(8) Linux Programmer's Manual KBDRATE(8)
NAME
kbdrate - reset the keyboard repeat rate and delay time
SYNOPSIS
kbdrate [ -s ] [ -r rate ] [ -d delay ]
DESCRIPTION
kbdrate is used to change the keyboard repeat rate and delay time. The delay is the amount of time that a key must be depressed before it
will start to repeat.
Using kbdrate without any options will reset the repeat rate to 10.9 characters per second (cps) and the delay to 250 milliseconds (ms) for
Intel- and M68K-based systems. These are the IBM defaults. On SPARC-based systems it will reset the repeat rate to 5 cps and the delay to
200 ms.
OPTIONS
-s Silent. No messages are printed.
-r rate
Change the keyboard repeat rate to rate cps. For Intel-based systems, the allowable range is from 2.0 to 30.0 cps. Only certain,
specific values are possible, and the program will select the nearest possible value to the one specified. The possible values are
given, in characters per second, as follows: 2.0, 2.1, 2.3, 2.5, 2.7, 3.0, 3.3, 3.7, 4.0, 4.3, 4.6, 5.0, 5.5, 6.0, 6.7, 7.5, 8.0,
8.6, 9.2, 10.0, 10.9, 12.0, 13.3, 15.0, 16.0, 17.1, 18.5, 20.0, 21.8, 24.0, 26.7, 30.0. For SPARC-based systems, the allowable
range is from 0 (no repeat) to 50 cps.
-d delay
Change the delay to delay milliseconds. For Intel-based systems, the allowable range is from 250 to 1000 ms, in 250 ms steps. For
SPARC systems, possible values are between 10 ms and 1440 ms, in 10 ms steps.
-V Display a version number and exit.
BUGS
Not all keyboards support all rates.
Not all keyboards have the rates mapped in the same way.
Setting the repeat rate on the Gateway AnyKey keyboard does not work. If someone with a Gateway figures out how to program the keyboard,
please send mail to util-linux@math.uio.no.
All this is very architecture dependent. Nowadays kbdrate first tries the KDKBDREP and KIOCSRATE ioctls. (The former usually works on an
m68k machine, the latter for SPARC.) When these ioctls fail an ioport interface as on i386 is assumed.
FILES
/etc/rc.local
/dev/port
Linux 1.1.19 22 June 1994 KBDRATE(8)