08-02-2001
I believe the interface of Quad_card should be qfe0 not qe0.
*The /etc/hostname.qfe0 file must contain the host name for the appropriate network interface.
*The host name should have an IP address that will need to be entered in the /etc/hosts file.
*The host name should be different from any other host name of any other interface, for example: /etc/hostname.hme0 and /etc/hostname.qfe2 cannot share the same host name.
Then, you should get those interfaces associated with their ip addr after rebooting.
Hope this help
9 More Discussions You Might Find Interesting
1. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
2. Solaris
Hi ......
I'm trying to configure my Solaris servers with only one NIC card to have 2 IP addresses as well as 2 different default gateways.
( NOT to be confused with multi-pathing - with 2 physical IPs & 1 virtual ip)
Thanks,
Remi (1 Reply)
Discussion started by: Remi
1 Replies
3. UNIX for Dummies Questions & Answers
hi all,
i've got an old PC with unix (SCO System V/386 rel. 3.2) on it.
Pentium I; 128mb; ISA 2-port RS232 serial adapter card for an oki dot-matrix printer. (no usb, no CD)
i've been running an old cobol program to do some invoicing and print reports.
some time back i changed the... (0 Replies)
Discussion started by: frankpky
0 Replies
4. SCO
hello everybody,
i am a new user for sco OS , i want to know how i can configure a graphical card under this system.
and usb DAT plzzz (0 Replies)
Discussion started by: lid-j-one
0 Replies
5. UNIX Desktop Questions & Answers
Does Red Hat Fedora support Nvidia card 8800GTX and 260 card?
Does any Linux OS support Nvidia card? (1 Reply)
Discussion started by: sito
1 Replies
6. UNIX for Dummies Questions & Answers
I want to connect to the internet via Wi-Fi, but I need to configure my pci adapter card for it to work. The adapter I am using is a Linksys Wireless-G pci adapter wmp54gs.:confused: (5 Replies)
Discussion started by: ryan352333
5 Replies
7. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
8. Shell Programming and Scripting
hi I juts want to know if there is a command that checks if an ethernet port corresponds to a network card.
ex. I have 3 network cards, one is two ports, and the other two 8 ports.
How do I know that eth0 corresponds to the the two-port network card and eth9 corresponds to the first 8-port... (2 Replies)
Discussion started by: h0ujun
2 Replies
9. Solaris
please find the below o/p for your reference
bash-3.00# fcinfo hba-port
HBA Port WWN: 21000024ff295a34
OS Device Name: /dev/cfg/c2
Manufacturer: QLogic Corp.
Model: 375-3356-02
Firmware Version: 05.03.02
FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies
LEARN ABOUT OPENSOLARIS
hostconfig
hostconfig(1M) System Administration Commands hostconfig(1M)
NAME
hostconfig - configure a system's host parameters
SYNOPSIS
/usr/sbin/hostconfig -p protocol [-d] [ -h] [-n] [-v]
[-i interface] [-f hostname]
DESCRIPTION
The hostconfig program uses a network protocol to acquire a machine's host parameters and set these parameters on the system.
The program selects which protocol to use based on the argument to the required -p flag. Different protocols may set different host param-
eters. Currently, only one protocol (bootparams) is defined.
OPTIONS
The following options are supported:
-d Enable debug output.
-f hostname Run the protocol as if this machine were named hostname.
-h Echo the received hostname to stdout, rather than setting hostname using the system name directly.
-i interface Use only the named network interface to run the protocol.
-n Run the network protocol, but do not set the acquired parameters into the system.
-p protocol Run hostconfig using protocol. Currently, only one protocol (bootparams) is available. This option is required.
Specifying the -p bootparams option uses the whoami call of the RPC bootparams protocol. This sets the system's hostname,
domainname, and default IP router parameters.
-v Enable verbose output.
EXAMPLES
Example 1 Configuring Host Parameters with Verbose Output
The following command configures a machine's host parameters using the whoami call of the RPC bootparams protocol with a verbose output.
example# hostconfig -p bootparams -v
Example 2 Displaying Host Parameters
The following command displays the parameters that would be set using the whoami call of the RPC bootparams protocol.
example# hostconfig -p bootparams -n -v
Example 3 Configuring Host Parameters Less the System Name
The following command configures a machine's host parameters, less the system name, using the whoami call of the RPC bootparams protocol.
example# hostconfig='hostconfig -p bootparams -h'
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
hostname(1), domainname(1M), route(1M), attributes(5)
SunOS 5.11 6 Nov 2000 hostconfig(1M)